ICC错误集锦.doc

ICC错误集锦 看懂ICC AVR的报错一、正常编译通过CODE:C:iccbinimakew -f main.mak iccavr -c -IC:iccinclude -e -DATMEGA -DATMega16 -l -g -Mavr_enhanced D:桌面实验教程LED应用霓虹灯main.c iccavr -o main -LC:icclib -g -ucrtatmega.o -bfunc_lit:0x54.0x4000 -dram_end:0x45f -bdata:0x60.0x45f -dhwstk_size:16 -beeprom:1.512 -fihx_coff -S2 main.lk -lcatmegaDevice 1% full.Done.这是我们最想看到的了，万事大吉。二、工程中未加入.C文件CODE:C:iccbinimakew -f main.mak iccavr -o main -LC:icclib -g -ucrtatmega.o -bfunc_lit:0x54.0x4000 -dram_end:0x45f -bdata:0x60.0x45f -dhwstk_size:16 -beeprom:1.512 -fihx_coff -S2 main.lk -lcatmegaunknown file type main.lk, passed to linker!ERROR unknown file type main.lkC:iccbinimakew.exe: Error code 1Done: there are error(s). Exit code: 1解决办法：将你的程序加入工程中，可以右键程序区ADD to project三、程序没有后缀名，或者后缀名不正确。CODE:C:iccbinimakew -f main.makC:iccbinimakew.exe: main is up to dateDone.这是一个很难理解的错误，它是由工程中的程序文件没有后缀名造成的。解决办法：将原有文件移出工程，将文件的后缀名改为.C，然后再加入工程中。四、没有main函数CODE:C:iccbinimakew -f main.mak iccavr -c -IC:iccinclude -e -DATMEGA -DATMega16 -l -g -Mavr_enhanced D:桌面实验教程LED应用霓虹灯main.c iccavr -o main -LC:icclib -g -ucrtatmega.o -bfunc_lit:0x54.0x4000 -dram_end:0x45f -bdata:0x60.0x45f -dhwstk_size:16 -beeprom:1.512 -fihx_coff -S2 main.lk -lcatmega!ERROR file crtatmega.o: undefined symbol _mainC:iccbinimakew.exe: Error code 1Done: there are error(s). Exit code: 1解决办法，编写程序主函数MAIN。五、没有选择目标芯片出现如下错误：CODE:C:iccbinimakew -f main.mak iccavr -c -IC:iccinclude -e -l -g -Wa-W D:桌面实验教程LED应用霓虹灯main.c iccavr -o main -LC:icclib -g -Wl-W -bfunc_lit:0.0x2000 -dram_end:0x25f -bdata:0x60.0x25f -dhwstk_size:16 -beeprom:1.512 -fihx_coff -S2 main.lk !E C:icclibcrtAVR.o(41): Code address 0 already contains a value!E C:icclibcrtAVR.o(41): Code address 0x1 already contains a valueC:iccbinimakew.exe: Error code 1Done: there are error(s). Exit code: 1解决办法：projectOptionstargetdevice configuration 选择合适的芯片。六、缺少分号CODE:C:iccbinimakew -f main.mak iccavr -c -IC:iccinclude -e -DATMEGA -DATMega16 -l -g -Mavr_enhanced D:桌面实验教程LED应用霓虹灯main.c!E D:桌面实验教程LED应用霓虹灯main.c(52): unrecognized statement!E D:桌面实验教程LED应用霓虹灯main.c(53): syntax error; found expecting ;!E D:桌面实验教程LED应用霓虹灯main.c(53): syntax error; found end of input expecting C:iccbinimakew.exe: Error code 1C:iccbinimakew.exe: main.o removed.Done: there are error(s). Exit code: 1上面的报告说明了第52行缺少一个分号，预期分号的地方出现了“”。解决方法，在52行末尾添加分号。类似的有：缺少的报错 CODE:C:iccbinimakew -f main.mak iccavr -c -IC:iccinclude -e -DATMEGA -DATMega16 -l -g -Mavr_enhanced D:桌面实验教程LED应用霓虹灯main.c!E D:桌面实验教程LED应用霓虹灯main.c(55): illegal statement termination!E D:桌面实验教程LED应用霓虹灯main.c(55): skipping void!W D:桌面实验教程LED应用霓虹灯main.c(55):warning calling function without prototype may cause errors!E D:桌面实验教程LED应用霓虹灯main.c(56): syntax error; found expecting ;!E D:桌面实验教程LED应用霓虹灯main.c(57): syntax error; found end of input expecting C:iccbinimakew.exe: Error code 1C:iccbinimakew.exe: main.o removed.Done: there are error(s). Exit code: 1七：变量没有定义CODE:C:iccbinimakew -f main.mak iccavr -c -IC:iccinclude -e -DATMEGA -DATMega16 -l -g -Mavr_enhanced D:桌面实验教程LED应用霓虹灯main.c!E D:桌面实验教程LED应用霓虹灯main.c(48): undeclared identifier iC:iccbinimakew