全文预览已结束
下载本文档
版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领
文档简介
1.0 Scope适用范围:(1) Refer to external parts of non-metallic material enclosing electrical parts and parts of insulating material supporting electric parts. (*19*)用于直接封闭电气部件的外部非金属材料和支承电气部件的绝缘材料。(2) Does not apply to decorative trims, knobs and other parts not likely to be ignited or to propagate flames originating from inside the toy. (*19.2*)该要求不适用于装饰性的饰件,手柄或其他不可能被点燃的或不可能传播源于玩具内部火焰的部件。(3) Generally, parts of non-metallic material shall be tested at 550C. (*19.2*)通常, 非金属材料部件应进行550C的测试。(4) Parts of insulating material supporting connections carrying a current exceeding 3A and a working voltage exceeding 12V should be tested at 650C. (*19.2.2*)对于用来支撑承载电流超过3A, 工作电压超过12V的连接件的绝缘部件,进行650C的灼热丝测试,(5) Parts of insulating material in contact with, or in close proximity (a distance not exceeding 3 mm) to, the connection carrying a current exceeding 3A and a working voltage exceeding 12V should be tested at 650C. (*19.2.2*)对于接触或接近(不超过3mm的距离)承载电流超过3A, 工作电压超过12V的部件的绝缘部件, 进行650C的测试.(6) Does not apply to parts supporting welded connections. (*19.2.2*)对于支承焊接连接件的部位不适用。(7) Does not apply to small parts, defined in EN 60695-2-11.对于EN 60695-2-11中定义的小部件不适用。2.0 Reference Documents参考文件:(1) The glow-wire test is made in accordance with EN 60695-2-11 and EN 60695-2-10.灼热丝测试要符合EN 60695-2-11 和 EN 60695-2-10的要求。(2)The operation manual of the glow-wire test apparatus. 灼热丝仪的操作手册3.0 Equipment测试设备:Glow wire test apparatus with灼热丝以及(1)flat smooth wooden board, having a minimum thickness of 10mm 厚度至少为10mm的平滑木板。(2)soft and strong, lightweight wrapping tissue, grammage between 12 g/m2 and 30 g/m2 柔软坚韧,轻的薄纸,克重在12 g/m2 到 30 g/m2之间。(2) wire brush.钢丝刷。Refer to clause 5 of EN 60695-2-11 for the further detail of the wooden board and the wrapping tissue.参考EN 60695-2-11第5章了解木板和薄纸的详细资料。4.0Procedure程序:4.1 Pre-conditioning预处理:(1) Place the specimen, the wooden board and the wrapping tissue to be used for 24h under the temperature 15oC t 35oC and the relative humidity 45% h 75%. 在温度为15oC t 35oC 和相对湿度为45% RH 75%的环境下将样品,木板和薄纸放置24小时。4.2 Specimen试样:(1) If possible, the test specimen should be a complete end-product. If the test cannot be made on a complete end-product, it is acceptable to如可能, 测试样品应为一完整制成品. 如果测试不能在一个完整制成品上进行, 则以下两种情况也可以接受:(i) cut a piece containing the part under examination from it, or切下一块含测试部位的小块, 或(ii) remove the part under examination in its entirety and test it separately.完整地取下要测试的部件来独立测试. (2) The test is made on one specimen. 测试是在一个样品上进行. 4.3Test Procedures测试步骤:(1)Before each series of test, it is necessary to inspect the glow-wire tip by measuring and recording the diameter of glow-wire tip. This shall be compared with subsequent tests and when this dimension is reduced to 90% of its initial reading then the glow-wire shall be replaced. 在一系列测试前,需要检查和记录灼热丝尖端的直径, 且要跟以后的测试进行比较,当尺寸减少到初始的90时,要更换灼热丝。(2) Arrange the sample such that, 安置样品:(i) The surface of the sample in contact with the tip of the glow wire is vertical and check it by placing a pendulous string beside the contact surface for verification. 接触灼热丝尖端的样品表面要垂直,在接触面旁边用一下垂细绳检验。(ii) The tip of the glow-wire is applied to the centre of the vertical surface which is likely to be subjected to thermal stresses in normal use. 尖端要顶到正常使用中可能承受热应力的垂直表面的中心位置 (iii) In cases where the areas subjected to thermal stresses during normal use of the equipment are not specified in detail, the tip of the glow-wire is applied at a place where the section is thinnest, but preferably not less than 15 mm from the upper edge of the specimen. 设备在正常使用中,受热应力的区域没详细规定情况下,灼热丝尖端施加到最薄的部位,但是距离试样上边缘最好不要少于15mm.Note: Clamping the sample onto the test apparatus shall not introduce excessive internal mechanical stresses in the test specimen during the test.注: 将试样在测试装置上夹紧,但在测试中不能因此给试样带来过度的内部机械应力).(3) The glow-wire is electrically heated up to 550C or 650C. The temperature and the heating current shall be constant within 5K for a period of at least 60s.灼热丝加热到550C 或650C,在60秒内,加热电流应使温度保持在5K以内Note:Care shall be taken to ensure that:Heat radiation does not influence the test specimen during this period by providing an adequate distance i.e. 5.0 cm minimum, or by using an appropriate screen.No further adjustment to the heating current or voltage is to be made until after the test is completed. 注:要小心注意保证::为使这期间内热辐射不影响测试样品,要有足够的距离如最少5.0cm,或者用一个适当的屏风隔开。在测试结束前不需要进一步调整加热电流或电压。(4) The tip of glow wire is brought slowly into contact with the specimen. It should be maintained in contact with the glow wire for 30 1s. 灼热丝的尖端缓慢地移近并接触试样。试样要保持与灼热丝接触30 1s。Note: An approximate rate of approach and withdrawal of 10 mm/s to 25 mm/s has been found to be satisfactory. However, the rate of approach shall be reduced to near zero upon contact to avoid forces of impact exceeding 1.0 N 0.2 N.In those cases where the material melts away from the glow-wire, the glow-wire shall not be kept in contact with the test specimen. 前进和后退速度大约为10mm/s到25mm/s之间比较合适。然而, 当接触时前进的速度应减小到零以避免施加压力而使得冲击力超过1.0N 0.2 N。当灼热丝在远离测试材料时,材料就已熔化, 那么灼热丝就不应与测试样品保持接触。(5) Then the glow-wire and the specimen are slowly separated avoiding any further heating of the test specimen and any movement of air which might affect the result of the test. 然后灼热丝与样品缓慢分开以避免因样品过热和因任何空气流动而影响测试结果。Note: The penetration of the tip of the glow-wire into and through the test specimen shall be limited to 7 mm 0.5 mm.注: 灼热丝的尖端穿过或穿透测试样品的厚度限定在7 mm 0.5 mm.(6) During application of the glow-wire (ta), and during a further period of 30s, the specimen, the parts surrounding the specimen and the layer placed below it shall be observed and the following shall be reported :在灼热丝(ta)施加测试的时间, 和以后的30s内, 都要观察试样、试样周围部件和放置在样品下面的层, 并报告以下情况: (i) the duration (ti) from the beginning of tip application up to the time at which the specimen or the specified layer placed below it ignites; 从灼热丝尖端接触试样到试样或布置在下面的规定层点燃的时间(ti);(ii) the duration (te) from the beginning of tip application up to the time when flames extinguish during or after the period of application; 在施加测试时或施加测试后,从灼热丝尖端接触试样到火焰熄灭的时间(te)(iii) the maximum height of any flame rounded up to the next 5 mm but disregarding the start of the ignition, which may produce a high flame for a period of approximately 1s; 除点燃初始时的火焰高度值的任何其他火焰高度的最大值, 取值以5mm的倍数记录(可能产生持续时间约1s的高火焰);Note: The height of the flame is the vertical distance measured between the upper edge of the glow-wire, when applied to the specimen, and the visible tip of the flame, when viewed in subdued light. 注:火焰高度是从灼热丝上边沿(施加到样品时)到可见火焰顶端(在柔和灯光下观察到的)之间测得的垂直距离.(iv) if a test specimen passes the test by virtue of most of the flaming material being withdrawn with the glow-wire, then this shall be reported in the test report. 如果测试试样是由于大部分可燃材料能承受灼热丝而通过这测试,则这要在测试报告上写明(v) Any ignition of the specified layer placed underneath the test specimen.放置在试样下面的规定层出现的任何点燃现象(7) On completion of each test, it is necessary to clean the tip, if necessary,
温馨提示
- 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
- 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
- 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
- 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
- 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
- 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
- 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
最新文档
- GB/T 26832-2026无损检测仪器钢丝绳电磁检测仪技术条件
- 简述多重耐药菌防控操作流程
- 2027年寒假开学摸底考试三年级英语测试卷
- 高二化学复习卷(2027年5月模拟考试)
- 八年级化学复习卷(2026-2027学年上学期单元测试)
- 2027年春季开学考试高三地理练习卷
- 2027年寒假开学摸底考试八年级化学基础卷打印版
- 2027年内蒙古中考二模历史试卷
- 儿童失踪紧急响应与搜寻指导书
- 游戏开发行业软件工程师绩效衡量表
- 视频监控系统试运行调试报告
- 4.1妈妈教学设计
- 神经内科诊疗新技术
- 非煤矿山安全生产管理与技术培训
- 双侧前庭病诊断与治疗专家共识
- 110kV变电站电气调试实施方案
- 八年级物理第二学期期中考试质量分析
- 心脏MRI在急性心肌梗死诊断中的临床价值与应用
- 两品一械培训
- 2026 年离婚协议书 2026 版民政局专用模板
- GB/T 7714-2025信息与文献参考文献著录规则
评论
0/150
提交评论