已阅读5页,还剩6页未读, 继续免费阅读
版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领
文档简介
New CCII Current Conveyor By John Robinson Mar 27 2008 Abstract Offering higher bandwidth than its voltage feedback counterpart the second generation current conveyor operational amplifier CCII can be used in RF mixers high frequency precision rectifiers and medical applications such as electrical impedance tomography The conventional operational amplifiers cannot be used in the high frequency applications due to their limited gain bandwidth product Introduction The current conveyor has been around since the original design or CCI which can be regarded as an ideal transistor was initially proposed by Smith and Sedra in 1968 CCI was then replaced by a more versatile second generation device in 1970 the CCII Current conveyor designs have mainly been BJT due to their high transconductance values compared to their CMOS counterparts They are used as current feedback operational amplifiers such as the MAX4223 low power amplifier which features current feedback rather than the conventional voltage feedback used by standard operational amplifiers This means that the current feedback operational amplifier is not restricted by the conventional gain bandwidths of a standard operational amplifier and can offer a much higher bandwidth solution than its voltage feedback counterpart Current conveyors are used in high frequency applications where the conventional operational amplifiers cannot be used because the conventional designs are limited by their gain bandwidth product In theory the current conveyor is only limited by the ft of the transistors used in its design Some applications where current conveyors are used today include RF mixers high frequency precision rectifiers and medical applications such as Electrical Impedance Tomography EIT A Bipolar Conveyor The diagram in Figure 1 below shows a current conveyor implemented using bipolar devices Figure 1 A bipolar CCII From Figure 1 it can be seen that the CCII conveyor can be modelled as an ideal transistor Y being the base gate X being the emitter source Z being the collector drain This type of circuit works well as a circuit with BJTs as the transconductance and Early voltages of BJTs are much greater than that of CMOS devices Therefore current conveyors work well as source followers Gain X Y is close to 1 Z has a natural high output impedance which cannot be mimicked by their CMOS counterparts The CMOS Source Follower As previously explained the major problem with a CMOS follower is the low gm and poor Early voltage 1 lambda This equates to poor gain because the gain for a voltage follower heavily relies on these two parameters to be large This can be observed in the equation below Where gL is the load conductance gds is the drain source conductance and gm is the transconductance of the CMOS device A typical simulated gain with a TSMC 0 18 m with a load of 1k gave a gain of 0 7 Compared to the ideal gain of 1 this represents a 30 loss in output gain Current Conveyor Source Follower One can use an unbuffered amplifier Figure 2a to mimic a source follower with a gain of one Then this modification can be added to the basic design in Figure 1 to make a CCII current conveyor Figure 2a A simple source follower Figure 2a can be implemented as shown below in Figure 2b Figure 2b The CCII unbuffered source follower and implementation From Figure 2b it can be seen that output X is fed back to one of the long tail pairs of inputs X The other input to the long tail pair is Y as input Y changes the current through M1 M2 differs as M3 and M4 is a current mirror There is a current difference between M2 and M4 This imbalance is addressed by pulling current from or to the gate source capacitance Cgs of device M5 Until the output X matches that of Y the bandwidth limit is defined as the rate at which this transistor can be discharged and charged Thus the bandwidth limit can be defined as Current Conveyor CCII Using an Unbuffered Amplifier From Figure 2 the first part of the current conveyor CCII can be realized To build the rest of the current conveyor CCII the current from output X simply has to be mirrored To give Z s output see the example in Figure 3 Figure 3 The current conveyor CCII using an unbuffered amplifier The current from M5 M6 is simply mirrored by M7 M8 giving the output Z of the CCII The output impedance of Z can be improved by adding in a cascode to M7 M8 if necessary One must be aware that to mimic the current successfully the output impedance of X must match that of Z i e the same transistor types and confirmation must be used on M5 M6 as on M7 M8 The gain of the CCII is simply Converting from a CCII to a CCII Taking the bias point Yb Figure 3 simply add the extra connections as shown in Figure 4 Figure 4 The current conveyor configured as a CCII From Figure 4 if all transistor dimensions are the same and if Yb the bias point from Figure 3 is taken then a current 2i is generated from M10 and M11 This is mirrored by M9 to give a current of 2i through M13 M12 provides a current of i and gives a current of i through Z thus giving a true CCII output There is a problem with this approach the Z now has an i DC term instead of a i term Consequently a 2i DC term needs to be added to the output of Z to compensate for i Figure 5 below shows the addition Figure 5 The CCII output with added DC bias From Figure 5 transistors M14 and M15 provide the appropriate current to compensate for the DC current taken by M13 Note that M14 and M15 must match M12 Make the current through R3 equal to i DC i Remember that R3 and R2 must match any mismatch in their values will mean that their output DC values will differ The VBIAS Circuit To create the necessary and appropriate voltage VDCBIAS that will maintain the DC currents in M14 and M15 then VDCBIAS Figure 5 must have the same DC value as Node Yb Figures 4 and 5 To do this simply mimic the front end stage and take the DC value of the input signal as the input bias voltage into this stage VINDC as shown in Figure 6 below Figure 6 VBIAS circuit for the DC compensation circuit Figure 5 The only problem with this design is that another resistor R4 is needed and R4 must again match R2 and R3 Simulation Results Using the CCII as in Figure 3 and using a TSMC 0 18 m process with R1 1k and R2 1k results in a gain of 1 The 3dB bandwidth of the device was 2 5GHz and had a gain of 0 972 with a power supply reject ratio PSRR of 41dB These results were improved by using a cascode device to replace M5 M6 and M7 M8 which gave a bandwidth of 900MHz and an improved gain of 0 993 The PSRR was also improved at 51dB References K C Smith and A Sedra The Current Conveyor A New Circuit Building Block IEEE Proc Vol 56 1968 pp 1368 1369 C Toumazou John Lidgey Alison Payne Practical Integrated Current Conveyors Current Mode Circuits Techniques in Analog High Frequency Design July 1996 Chapter 5 2 pp 69 80 K C Smith and A Sedra A Second Generation Current Conveyor and its Applications IEEE Trans CT 17 1970 pp 132 134 This application note is based on an article published in Chip Design Magazine August September 2007 Related Parts MAX4112Single Dual Quad 400MHz Low Power Current Feedback Amplifiers MAX477300MHz High Speed Op Amp 新型 CCII 电流传输器 John Robinson Jul 23 2008 摘要 第二代电流传输器运算放大器 CCII 与采用电压反馈的类似器件相比可以提供更宽的频 带 适用于RF混频器 高频精密整流器以及医疗产品 例如 电阻抗断层成像系统 传统的 运算放大器受其增益带宽积限制 不能胜任高频应用 概述 电流传输器或 CCI 可以看作一个理想的晶体管 的概念最初是由 Smith 和 Sedra 于 1968 提出 的 之后 在 1970 年 CCI 被更加通用的第二代器件 CCII 所取代 现在的传输器设计主要采 用 BJT 它们与 CMOS 相比具有更高的跨导 非常适合电流反馈运算放大器的设计 例如 MAX4112 低功耗放大器 其特点是电流反馈 而不是标准运算放大器中使用的电压反馈方式 因此 电流反馈运算放大器不像标准运算放大器那样受到增益带宽积的限制 它可以提供比电 压反馈器件更宽的频带 电流传输器通常用于传统运算放大器无法支持的高频产品 因为传统设计的增益带宽积有限 理论上讲 电流传输器只受设计中晶体管 ft的限制 目前采用电流传输器的应用主要包括 RF 混频器 高频精密整流器以及医疗产品 比如电阻抗断层成像系统 EIT 双极型传输器 图图 1 所示框图是使用双极型器件构成的电流传输器 图1 双极型CCII 从图 1 可以看出 CCII 传输器可以当作一个理想的晶体管模型 Y 是基极 栅极 X 是发射极 源极 Z 是集电极 漏极 这种利用 BJT 构成的电路能够很好地工作 因为 BJT 的跨导和 Early 电压比 CMOS 器件高 因此 电流传输器可以很好地用作源极跟随器 增益 X Y 接近于 1 Z 具有高输出阻抗 这是 CMOS 电路望尘莫及的 CMOS 源极跟随器 如同上述说明 CMOS 跟随器的主要问题是 gm和 Early 电压 1 lambda 较低 等同于低增益 因为电压跟随器的增益很大程度上依赖于这两个参数的提高 通过下式可以看到这个关系 式中 gL是负载电导 gds是漏源间电导 gm是 CMOS 器件的跨导 利用 TSMC 0 18 m 工艺 在负载为 1k 时 典型的仿真增益可以达到 0 7 同理想增益 1 相 比 存在 30 的输出增益损失 电流传输器源极跟随器 利用一个不带缓冲的放大器 图图 2a 可以模拟增益为 1 的源极跟随器 然后在图 1 设计的基础上 增加这一电路 构成 CCII 电流传输器 图2a 简单的源极跟随器 图 2a 可以按照下面的图图 2b 实现 图2b CCII无缓冲源极跟随器及其实现 从图 2b 可以看出输出 X 被反馈到长尾晶体管对的一个输入 X 长尾晶体管对的另一个输入是 Y 输入 Y 通过 M1 改变电流 M2 与 M3 不同 M4 是电流镜 M2 和 M4 之间存在电流差 从器件 M5 的栅极 源极电容 Cgs拉电流或馈入电流 可以解决不平 衡问题 在输出 X 与 Y 达到匹配之前 带宽限制定义为晶体管充电和放电的速率 因此 带宽 限制可以定义为 采用非缓冲放大器的电流传输器 CCII 按照图 2 可以实现电流传输器 CCII 的第一部分 为了完成电流传输器 CCII 的剩余部分 输出 X 电流只需进行镜像 参考图图 3 它给出了 Z 的输出电路 图3 采用无缓冲放大器的电流传输器 CCII M7 M8 对来自 M5 M6 的电流进行简单镜像 得到 CCII 的输出 Z 必要时 可以给 M7 M8 增加一个共源共栅结构 以提高 Z 的输出阻抗 需要注意的是 为了 正确模拟电流 X 的输出阻抗必须与 Z 匹配 比如 M5 M6 必须使用与 M7 M8 相同的晶体管 类型 CCII 的增益可简单表示为 从 CCII 转变为 CCII 选取偏置点 Yb 图 3 增加图图 4 所示附加连接 图4 电流传输器配置为CCII 图 4 中 如果所有晶体管规格一致 并且选取 Yb 图 3 中的偏置点 M10 和 M11 所产生的电 流将为 2i 通过 M9 镜像 在 M13 得到 2i 电流 M12 提供电流为 I 并通过 Z 提供电流 i 由此得到一个真正的 CCII 输出 这种方案存在一个问题 Z 有一个直流项 i 而不是 i 因 此 Z 输出需要增加 2i 的直流电流补偿 I 图图 5 提供了这个附加项 图5 增加直流偏置后的CCII 输出 图 5 中 晶体
温馨提示
- 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
- 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
- 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
- 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
- 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
- 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
- 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
最新文档
- 高中家庭课件
- g字夹设计课件
- 肝脏静脉系统课件
- 工装夹具设计课件
- 公众号制作培训课件
- 公众号转换课件
- 2026年商务策划(商业活动策划)试题及答案
- 桥梁湿接缝模板施工
- 公众号奖励机制课件
- 公众号发布课件
- T/CMEAS 079-2026院内快速反应体系建设规范
- 新教材部编人教版五年级上册道德与法治(课件)第1课开天辟地的大事变
- 2026年全国版图知识竞赛(小学组)练习题及答案
- 2011 氧化铝耐磨陶瓷复合衬板
- 赣南脐橙产业化发展:成就、困境与突破路径探究
- 知识产权专业专利代理就业方向
- JJG(吉) 145-2025 无创非自动电子血压计检定规程
- 农村小学“一生一档”学生成长记录表
- 江苏省南通市2026届高三上学期学业质量监测英语试题(含答案)
- 文学接受理论中“期待视野”的动态建构-基于姚斯《走向接受美学》读者反应模型
- 锚杆支护施工方案边坡加固方案
评论
0/150
提交评论