RD-MW16(16CH)1200W摇头灯说明书.doc

Instruction ManualPROFESSIONAL SHOW LIGHTRD-MW16 MOVING HEAD- Execution 2008-Congratulations on choosing our light! This equipment is powerful in functions with CE Standard. It has been tested through frequent practice in different cases, and well recognized by professional designers in the field of stage light. It fully shows the modern times light characteristic with good performance. It can be used in all kinds of scenes which need high quality lighting.Please read this manual carefully before powering or installing the fixture, follow the safety precautions listed below and observe all warnings in this manual.Warning: always disconnect from mains supply before replacing the lamp.1. Disconnect the fixture form AC power before removing or installing the lamp, fuses, or any part, and when not in use.2. Always make the fixture connected to the ground electrically.3. Do not expose the fixture to rain or moisture.ParameterLamp：HMI-1200W/SColor wheel:：2colors wheelsSize：64*62*91CMWeight:：58KGSOthers: 20 DMX512 channels, double color wheel, LCD DISPLAY INSTALL AND REPLACE LAMP1、 Unscrew the 4 screws at the back of the fixture, then pull out the lamp socket.2、 If changing the lamp, remove the old lamp from the socket.3、 Holding the new lamp, align the small pin on the lamp with the small hole in the socket and insert the lamp squarely. 4、 Align the screw holes and fasten the lamp access plate with 2 screws.5、 Please check whether the lamp was fixed tightly. Otherwise, poor connection may lead to short-circuit discharge under high voltage.POWER SUPPLY MAINSUse the plug provide to connect the mains power to the projector paying attention to the voltage and frequency marked on the panel of the projector. It is recommended that each projector be supplied separately so that they may be individually switched on and off.IMPORTANTIt is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards. Power consumption of this projector is 2000W.WATCHDOG SYSTEMWhen the projector is switched on the electronics perform a reset, this function moves the head to an extreme limit point and rotates the internal color and gobo wheels thus allowing the microprocessor control system to register the positions of all motors under its control. When the lamp strikes and fires up, it can create a certain amount of electrical noise within the projector that has the potential to disturb the microprocessor. This projector is fitted with an electronic watchdog system that monitors the microprocessor and will initiate a reset if the functioning of the microprocessor has been disturbed. This system ensures that the reset is performed successfully and once completed the projector is ready to receive control instructions and operate without problem.Mounting bracketSPOT-2008 can be placed on the ground or hanging installation in any position. The lock system makes it quick and simple to install bracket to four locations, see Figure Warning! Hook fastener must be in place, steel piece is locked with nut, When uninstalling, use a finger to pull the steel piece up, and then drop out the hook fastener. Warning! Insurance rope must be tied at the additional hole in the bottom, and never be tied at the handle. DMX PARAMETERDMX 通道（CH）范围（VALUE）详细功能（FUNCTION）1、光圈（Iris）0-255光圈由大到小Iris2、颜色盘1(磁定位)(color wheel-1)0-100101-191192-255颜色连续可调白光到色盘7依次变换色盘由慢到快的旋转3、颜色盘2(磁定位)(color wheel-2)0-255颜色连续可调白光到色盘7依次变换色盘由慢到快的旋转4、光闸（shutter）/ strobe0-127128-139140-247248-255线性调光光闸打开频闪速度由慢到快1-7Hz光闸打开5、X轴（Pan）0-255水平面内线形旋转5406、Y轴(Tilt)0-255垂直面内线形旋转2707、X轴(Pan 16BIT)0-255X轴16BIT8、Y轴(Tilt 16BIT)0-255Y轴16BIT9、速度调节(pan/tilt speed)0-255XY速度由快到慢fast - slow10、色温较正(Color Temperature)05152-103104-155156-207208-255白光色温6000K色温3200K雾化镜1四棱镜11、调焦(Focus)0-255线形无级调焦12. C0-25513. M0-25514. Y0-25515、放大(Zoom)0-255放大16、系统复位(Reset)0-234235-239240-255空操作数据保持3S后系统复位空操作LCD DISPLAY OPERATIONDisplay valueFunctionSystem ResetAuto Tmac2000系统复位状态Auto Tmac2000DMX AddressAddress 001标准DMX512 地址地址选择状态001-511(按UP/DOWN 选择ENTER 确认)Pan InverNoX轴反向功能状态(按UP/DOWN 选择yes or no ENTER 确认)Tilt InverNoY轴反向功能状态System ResetNo系统复位状态按UP/DOWN 选择yes or no ENTER 确认Speed AdjustX&Y Track 0速度设置X/Y轴速度选择快-慢(按UP/DOWN 选择Track0-3 ENTER 确认Install and replace lamp, the attentions are as follows:MSD lamps average life is 750 hours, please check if it works out before replace it .draw out the line of power supply.Cool the bulb for 10-15 minutes after if blacks out ,then tweak the four screws. Open the cover, get the old bulb out and insert the new one.Cleaning of lens system Wash exterior and interior optical mirrors to enhance the brightness in regular time, especially when equipment used in messy surroundings . Use mirror cleanser (or alcohol) to wash exterior mirrors in every 15/20 days, 40/60 days for interior focusing prism/reflector.The equipment not fit for cases belowRelative humidity is too high.Shake and hit. Room temperature is above 40 degree or below 0 degree.Relative temperature is below 30 degree of above 80 degree.Safety informationIn case of serious problems, stop using the equipment ,and refer it to the agent or factory for checking.Do not separate the light personally.Prevent liquid, water and metal into the equipment.Who to check this equipment must be well qualified.If the functional controller is used to ignite light, be cautious that the voltage will fall down immediately when many lamps are lighted. The solution to this is lighting the lamps in every five seconds one by one.When magnetic ballast is used, make sure it is five minutes after the bulb is cooled when relight the lamps. (electronic ballast can relight by heat)When pull out the line of power supply, do grip the insulated housing of the plug, do not draw the line directly.AlarmReplace the housing, lens and ultraviolet radiation when visible damage takes place, such as cracks.Replace the lamp when damage happens to it or its maximum life is used up.Shut off the power supply when replace lamp, safety box, and any other accessories and when it does not work.Keep the ground switch connected to ground.Power supply must meet the local standard on architecture and electric signal with overload protection and connect to earth.Do not make light beam shine on skin ,do not look at the light source directly.Prevent short circuit happening to temperature control switch and safety box. When replace defective fuse, choose approved new fuse of the same type.Keep the distance more than 1 M from equipment to flammable material (such as cloth, wood , paper).When housing of equipment feels very hot , cool it for 5 minutes before operation.Advise you to choose accessories produced by us when install and replace.Whenever install or move equipment, set an alarm to prevent others entering job site. Do not put your hand between side arm and light structure when light working.(shown in picture 1 by arrow)Keep the optical system clean. Made the maintenance according to this manual