关 键 词：

液压 钻机 设计 CAD 图纸 PDF

资源描述：

喜欢这套资料就充值下载吧。。。资源目录里展示的都可在线预览哦。。。下载后都有，，请放心下载，，文件全都包含在内，，【有疑问咨询QQ:414951605 或 1304139763】

内容简介：

摘 要1963年，设计民微型Hydrack钻机。这是一种非常轻而短的钻机，其行程为851mm。采用三速齿轮箱，其最大转矩为691Nm，有效钻孔推力为2145公斤。设计钻杆较小，直径为41.3mm，长为762mm，也带锥形螺纹接头，称为ET/A型钻杆。ET/A型和最初的ET/N型钻杆是抽放瓦斯的两种标准钻孔设备，现已包括在英国煤炭部第613/1974号样本中。钻机有一个带滑板的机架，由滑板支撑。钻头安装在滑座上，由液压马达、变速齿轮箱和推力套以及供水旋转接头组成。在机架内滑座下是液压缸。机架上钻孔末端的导向夹持器用来固定和支持钻杆。Hydrack钻机是由由组标准件装置组成；动力设备这是一个装有液压油的油箱，下面有滑橇，便于运输。一台电动机和液压泵及其它辅助设备，如回油过滤器、安全阀、加油泵、油箱通气管以及湿度安全开关都安装在油箱上面。控制盘为四个装置中最小的。包含有钻孔功能的控制阀，指示转矩的压力计以及钻头上的钻进压力。装配式机架当准备钻孔时，机架支撑着钻机。机架形式多种以适应不同钻孔地形变化，有H型机架、A型机架和单支柱支座。后两项是根据钻机使用者提出来的要求设计的。液压油通过挠性液压软管从动力装置站输送到控制盘，然后进入钻机。软管一般长4m，能适应各种装置的定位。关键词：动力设备 控制盘 装配式机架ABSTRACTHydrack gas drilling rig is the first for the electro-hydraulic drilling rig, the rig before most of the air-powered. Drill pipe and bit by a hydraulic motor through the rotating six-speed gear box; to be thrust into power and the trip from 815 mm to achieve the hydraulic cylinders, with rack and pinion system to process will be carried out twice. About the most torque 949 Nm, a way to about 1702 mm bit on the effective thrust of about 2,794 kg. Diameter drill pipe design for the 60.3 mm, for the 1524 mm long with a cone-shaped male connector, commonly known as EF / N-type drill pipe. 1963, the design of the micro-Hydrack rig. This is a very short period of Qinger drilling rig, his trip to 851 mm. A three-speed gear box, the largest of its torque to 691 Nm, effective drilling thrust 2,145 kg. Design drill pipe smaller diameter of 41.3 mm, length of 762 mm, also with cone-shaped male connector, called ET / A-type drill pipe. ET / A-type and the initial ET / N-type drill pipe is the drainage of two standard gas drilling equipment, including in the United Kingdom is now No. 613/1974 of the Ministry of Coal samples. Hydrack drilling rig is installed by the group composed of standard parts; Drill - a rack with skateboards, skateboards support. Bit installed in the sliding seat, by the hydraulic motors, Biansuchilun me and thrust as well as sets of component supply rotary joint. On the rack, slide under the hydraulic cylinder. Bored end of the rack-oriented holder used to support the drill pipe and fixed. Power equipment - which is equipped with a hydraulic oil tank, following a slip-ski, makes it easy to transport. A motor and hydraulic pump and other auxiliary equipment, such as the return to the oil filter, safety valve, and pumps, tank airway and humidity safety switches are installed in the fuel tank above. Control panel - the smallest of the four devices. Bored functions include the control valve, pressure gauge and the instructions of torque on the drilling bit pressure. Rack assembly - when the preparations for drilling, rack supports drilling rig. Rack to adapt to a variety of different forms of drilling terrain changes, H-rack, A-frame and single-bearing pillars. The latter two are based drilling rig users to the requirements of the design. Hydraulic oil through hydraulic flexible hose from the power plant station transmitted t