BrocadeFCIP配置手册

1、Brocade7800 FCIP 配置手册目录、环境 12、 清除GE口原有信息 23、 配置GE口类型 34、 创建ge0与gel口 IP 35、 创建IP路由 36、 创建FCIP隧道 47、 添加Circuit （电路） 58、 配置传输压缩 69、 建立lsan zone 6十、测试数据复制 7、环境BJSC-7800-01BJSC-7800-02清除GE 口原有信息BJSC-7800-02:admin> portshow fcipcircuit all显示电路信息Tunnel Circuit OpStatus Flags Uptime TxMBpsRxMBps ConnCnt

2、CommRt Met160 ge0 InProg -s 1m27s0.000.004 20/100 0161 ge1 InProg -s 18m14s0.000.004 30/90 0Flags: circuit: s=sack有2条电路，分别是 16 0与16 1BJSC-7800-02:admin> portcfgdefault ge0直接清除 ge0 口信息失败Circuit Configuration exists using this GE port.BJSC-7800-02:admin> portcfg fcipcircuit 16 delete 0需要先删除电路Ope

3、ration SucceededBJSC-7800-02:admin> portcfgdefault ge0清除 ge0 口信息成功Operation SucceededBJSC-7800-02:admin> portcfgdefault ge1同上Circuit Configuration exists using this GE port.BJSC-7800-02:admin> portcfg fcipcircuit 16 delete 1同上Operation SucceededBJSC-7800-02:admin> portcfgdefault ge1 同上Op

4、eration SucceededBJSC-7800-02:admin>portcfg fciptunnel 16 delete删除隧道shwitchshow 显示 GE 口结果ge0cu1GOnline FCIP Copperge1cu1GOnline FCIP Copperge2id1GNo_Light FCIPge3-1GNo_Module FCIPge4-1GNo_Module FCIPge5-1GNo_Module FCIPge0 电口ge1 电口Ge2 光口Ge3 光口Ge4 光口Ge5 光口当上面2个电口被使用后，下面的前 2个光口将不能使用。三、配置GE 口类型BJSC-

5、7800-01:admin> portcfggemediatypeUsage: portcfggemediatype GbE_port optical光 | copper 电BJSC-7800-01:admin>BJSC-7800-01:admin>例如：sw67:admin>portcfggemediatype GE0 optical四、创建ge0与gel 口 IPBJSC-7800-01:admin>portcfg ipif ge0 create 1500BJSC-7800-01:admin> portc

6、fg ipif ge1 create 1500BJSC-7800-01:admin> portshow ipif all 显示 GE口 IPPort: ge0Interface IPv4 Address NetMask Effective MTU Flags 0 1500 U R MPort: ge1Interface IPv4 Address NetMask Effective MTU Flags 0 1500 U R MFlags: U=Up B=

7、Broadcast D=Debug L=Loopback P=Point2Point R=Running N=NoArp PR=Promisc M=Multicast S=StaticArp LU=LinkUpBJSC-7800-01:admin>对端 BJSC-7800-02 配置 IP 为 GE0 GE1 五、创建IP路由测试环境直连方式可以 ping通对端，因此配置路由步骤可先忽略。 实际实施时不可省略此步。BJSC-7800-01:admin> portcmd -ping ge0 -s -d

8、Pinging from ip interface on 0/ge0 with 64 bytes of dataReply from : bytes=64 rtt=2ms ttl=20Reply from : bytes=64 rtt=0ms ttl=20Reply from : bytes=64 rtt=0ms ttl=20Reply from : bytes=64 rtt=2ms ttl=20Ping Statistics for :Packets

9、: Sent = 4, Received = 4, Loss = 0 ( 0 percent loss)Min RTT = 0ms, Max RTT = 2ms Average = 1msBJSC-7800-01:admin>六、创建FCIP隧道在第16VE口创建FCIP隧道（先写远端IP再写本端IP,后面的数字单位是 K）,两边都要创建BJSC-7800-01:admin> portcfg fciptunnel 16 create -b 50000 -B100000Operation Succeeded当仅仅本端建立好后，状态为InPro

10、gBJSC-7800-01:admin> portshow fciptunnel all显示隧道信息Tunnel Circuit OpStatus Flags Uptime TxMBps RxMBps ConnCnt CommRt Met 16- InProg - 0s 0.000.00 0-Flags: tunnel: c=compression f=fastwrite t=Tapepipelining F=FICON T=TPerf circuit: s=sackBJSC-7800-01:admin> portshow fcipcircuit all显示电路信息Tunnel C

11、ircuit OpStatus Flags Uptime TxMBps RxMBps ConnCnt CommRt Met160 ge0 InProg -s 0s 0.000.00 0 50/100 0Flags: circuit: s=sack当对端也建立好隧道后，状态为 UpTunnel Circuit OpStatus Flags Uptime TxMBps RxMBps ConnCnt CommRt Met 16 - Up 3m40s 0.10 0.01 1 - Flags: tunnel: c=compression f=fastwrite t=Tapepipelining F=FI

12、CON T=TPerf circuit: s=sackBJSC-7800-01:admin> portshow fcipcircuit allTunnel Circuit OpStatus Flags Uptime TxMBps RxMBps ConnCnt CommRt Met16 0 ge0 Up-s 3m49s0.070.01 1 50/100 0Flags: circuit: s=sackBJSC-7800-01:admin>创建好隧道后，0电路也就存在了，并且已经存在于16隧道中。下面要添加 1电路到16隧道中。七、添加Circuit（电路）将Circuit （电路）放到

13、16隧道，编号为1。BJSC-7800-01:admin> portcfg fcipcircuit 16 create 1 -b 50000-B 100000Operation SucceededBJSC-7800-01:admin>两边都要操作添加，第一个 IP为目标，第二个IP为本地BJSC-7800-01:admin> portshow fcipcircuit allTunnel Circuit OpStatus Flags Uptime TxMBps RxMBps ConnCnt CommRt Met160 ge0Up-s22m

14、22s0.020.012 50/1000161 ge1Ups 10s0.000.00 150/100 0Flags: circuit: s=sackBJSC-7800-01:admin>八、配置传输压缩两边都要改，建议使用中等压缩比，数字表示为 2,高压缩比是3,不建议3.也不建议1.BJSC-7800-01:admin> portcfg fciptunnel 16 modify -c 2九、建立lsan zone两边都要建立BJSC-7800-01:admin>zonecreatelsan_zone","50:06:0e:80:04:29:3f:12;5

15、0:06:0e:80:04:29:3f:32”Zone成员的 wwn来自两台7800所接的存储78001 为 4450:06:0e:80:04:29:3f:12010400idN2OnlineFC F-Port78002 为 4450:06:0e:80:14:38:cc:11010400idN2OnlineFC F-PortBJSC-7800-01:admin> cfgcreate "lsan_cfg","lsan_zone"BJSC-7800-01:admin> cfgenable lsan_cfgBJSC-7800-01:admin>

16、; cfgshowDefined configuration: cfg: lsan_cfg lsan_zone zone: lsan_zone50:06:0e:80:04:29:3f:12; 50:06:0e:80:14:38:cc:11Effective configuration: cfg: lsan_cfg zone: lsan_zone50:06:0e:80:04:29:3f:1250:06:0e:80:14:38:cc:11BJSC-7800-01:admin>添加其他存储端口到lsan zoneBJSC-7800-01:admin>zoneadd"lsan_z

17、one","50:06:0e:80:04:29:3f:32;50:06:0e:80:14:38:cc:3TcfgdisablecfgenableDefined configuration: cfg: lsan_cfg lsan_zone zone: lsan_zone50:06:0e:80:04:29:3f:12; 50:06:0e:80:14:38:cc:11; 50:06:0e:80:04:29:3f:32; 50:06:0e:80:14:38:cc:31Effective configuration: cfg: lsan_cfg zone: lsan_zone50:0

18、6:0e:80:04:29:3f:1250:06:0e:80:14:38:cc:11 50:06:0e:80:04:29:3f:32 50:06:0e:80:14:38:cc:31BJSC-7800-01:admin>十、测试数据复制HDST程师在USP存储配置界面上可以看到2条连路已经连通。新建2个LUN并作数据复制。(截图略)可以看到数据传输信息和压缩比BJSC-7800-01:admin> portshow fciptunnel all -p Tunnel ID: 16Tunnel Description:Admin Status: EnabledOper Status: UpCompression: On (Moderate)Fastwrite: OffTape Acceleration: OffTPerf Option: OffIPSec: DisabledRemote WWN: Not ConfiguredLocal WWN: 10:00:00:05:33:2d:47:acPeer WWN: 10:00:00:05:33:31:60:fcCircuit Count: 2Flags: 0x00000000FICON: OffOper Status: UpFlow Ctrl State: OffConnected