结构工程图标注的方法与技巧2016-3-17(1)

1、Goertek Proprietary and Confidential Background Technology and IP. Do Not Disclose to Unauthorized Parties.Prepared By: GoerTekDate: 03/02/2016Goertek Proprietary and Confidential Background Technology and IP. Do Not Disclose to Unauthorized Parties.2线性尺寸标注角度尺寸标注圆/圆弧尺寸标注小尺寸标注Goertek Proprietary and

2、Confidential Background Technology and IP. Do Not Disclose to Unauthorized Parties.3Goertek Proprietary and Confidential Background Technology and IP. Do Not Disclose to Unauthorized Parties.4Goertek Proprietary and Confidential Background Technology and IP. Do Not Disclose to Unauthorized Parties.5

3、Tuba Bottom coverGoertek Proprietary and Confidential Background Technology and IP. Do Not Disclose to Unauthorized Parties.6Goertek Proprietary and Confidential Background Technology and IP. Do Not Disclose to Unauthorized Parties.7Goertek Proprietary and Confidential Background Technology and IP.

4、Do Not Disclose to Unauthorized Parties.81. 技术要求2. 详细尺寸参照3D文件： ray_3d_bottom_housing.prt.1 ；3. 产品材质：PC7015-10 ;颜色：Black；表面处理：VDI 24; 4. 禁止使用水口料，水口修剪平至设计胶位或以下；5. 3D 图中未做拔模斜度0.5 max.(指后模部份)；3D 图中未倒圆角R0.20mm max.；6. 零件表面分模线最高允许高度：0.03mm；7. 零件不得有缩水、顶白、划伤、拖花、披锋，流痕以及其他缺陷；8. 进胶口、分模线、顶针、斜顶，行位等模具结构必须由歌尔公司结构工

5、程师确认；9. 顶针痕迹要低于设计胶位00.05mm；模具及产品的各类标示做成凹字(字深0.15mm MAX)10. 符合Goertek产品环保标准;11. 其他环保要求：无Goertek Proprietary and Confidential Background Technology and IP. Do Not Disclose to Unauthorized Parties.9Goertek Proprietary and Confidential Background Technology and IP. Do Not Disclose to Unauthorized Partie

6、s.10Goertek Proprietary and Confidential Background Technology and IP. Do Not Disclose to Unauthorized Parties.111. 技术要求2. 详细尺寸参照3D文件： ray_3d_bottom_housing.prt.1 ；3. 产品材质：PC7015-10 ;厚度：0.2mm.颜色：黑色;表面处理：镀镍; 4. 产品周围压毛边,锐角倒钝角；5. 符合Goertek产品环保标准;6. 其他环保要求：无Goertek Proprietary and Confidential Backgroun

7、d Technology and IP. Do Not Disclose to Unauthorized Parties.12技术要求1. 产品材质：SUS304 ;.颜色：黑色;表面处理：镀镍; 2. 产品周围压无压痕，产品表面要清洗，铁屑，油污；3. 电镀要求：盐雾测试要过48H以上；4. 符合Goertek产品环保标准;5. 其他环保要求：无Goertek Proprietary and Confidential Background Technology and IP. Do Not Disclose to Unauthorized Parties.13技术要求1. 产品材质：3M 9075 ;颜色：黑色;厚度：T=0.05mm2. 产品周围压无压痕，产品要整洁，无褶皱，无毛屑等；3. 符合Goertek产品环保标准;4. 其他环