技术要求中英对照

1、I. SUMMARY OF NOTES技术要求汇总SHEET METAL钣金： NOTES技术要求（喷涂）：1. INNER BENDING RADII TO BE R_ UNLESS OTHERWISE SPECIFIED未注内折弯圆角R_2. REMOVE ALL SHARP EDGES AND CORNERS 去除毛刺锐边3. DIMENSIONS ARE TO THEORETICAL SHARP CORNERS尺寸标注为到理论尖角的尺寸4. FINISH: POWDER COATING表面处理： 喷粉NOTES技术要求（镀锌）：1. INNER ENDING RADII TO BE R

2、_ UNLESS OTHERWISE SPECIFIED未注内折弯圆角R_2. REMOVE ALL SHARP EDGES AND CORNERS 去除毛刺锐边3. DIMENSIONS ARE TO THEORETICAL SHARP CORNERS尺寸标注为到理论尖角的尺寸4. FINISH: Fe/Zn_ /D (GB/T 9799, ISO20811)表面处理：Fe/Zn_ /D (GB/T 9799, ISO20811)NOTES: RECOMMEND Fe/Zn5 /D FOR 120H SALT FOG TEST REQUIREMENT AND Fe/Zn12 /D FOR 1

3、92H SALT FOG TEST REQUIREMENT PER ASTM B117.注：对于按照ASTM B117要求，120小时盐雾试验要求的推荐电镀Fe/Zn5 /D，192小时盐雾试验要求的推荐电镀Fe/Zn12 /D. 铜母排COPPER BUSBAR: NOTES 技术要求 (镀锡)： 1. INNER ENDING RADII TO BE R_ UNLESS OTHERWISE SPECIFIED未注内折弯圆角R_；2. FINISH: BRIGHT TIN PLATING PER ASTM B545按照ASTM B545规定镀亮锡TIN PURITY: 99.0%, GRAD

4、E: B BRIGHT, CLASS: B, THICKNESS: 5 TIN PURITY: 99.0%, GRADE: B BRIGHT, CLASS: B, THICKNESS: m锡纯度：99%， 等级：电镀亮锡， 类型：B， 厚度 m;3. OTHER NON PLATING SURFACE TO COVER BY HEAT SHRINKABLE TUBING其余非指定电镀区域用批准的高压热缩套;4. COPPER CONDUCTIVITY SHALL BE NO LESS THAN 97%IACS 铜导电率不低于97% IACS.NOTES 技术要求(镀银)： 1. INNER E

5、NDING RADII TO BE R_ UNLESS OTHERWISE SPEICIFIED 未注内折弯圆角R_；2. FINISH: SILVER PLANTING PER ASTM B700表面处理：按照ASTM B700镀银SILVER PURITY: TYPE3 98.0%, GRADE: B BRIGHT, CLASS: N, THICKNESS: 5m银纯度：3型98%， 等级：亮银B级， 类型：N， 厚度5 m3. OTHER NON PLATING SURFACE TO COVER BY HEAT SHRINKABLE TUBING 其余非指定电镀区域用批准的高压热缩套。4

6、. COPPER CONDUCTIVITY SHALL BE NO LESS THAN 97%IACS铜导电率不低于97% IACS.5. WELDING 焊装图1. WELDING TO BE SOLID AND FREE OF VOIDS, SLAG AND VOID WELDING焊缝牢固可靠，无气孔、夹渣和虚焊2. GRIND AFTER WELDED 焊后打磨 3. FINISH: PAINT 表面处理：喷漆Or或：FINISH: Fe/Zn_ /D (GB/T 9799, ISO20811)表面处理：Fe/Zn_ /D (GB/T 9799, ISO20811)ASSEMBLY装配

7、图：1. ALL FASTENERS USED TO BE GB/ISO GRADE 8.8 UNLESS OTHERWISE NOTED所用的紧固件除非特殊说明，强度均为国标8.8级2. FASTENERS TIGHTENING TORQUE PER SPEC 10110992P1 - Part B螺栓紧固扭矩按照技术条件10110992P1 B部分3. TO LUBRICANT ON THE RELATIVELY MOVING OR ROTATION PLACES WITH GREASE所有运动部件有相对运动处涂润滑脂INSULATED PARTS绝缘件：1. MATERIAL: 材料：2

8、. RADII TO BE R_ UNLESS OTHERWISE SPECIFIED 未注圆角R 3. COLOR OF PART: 零件颜色：4. UNSPECIFIED DAFT ANGLE: ° 未注拔模斜度：°5. PART TO BE FEE OF SHRINK CAVITY, PORE AND CRACK. PART SURFACE TO BE SMOOTH AND CLEAN WITHOUT MACULA AND MECHANICAL DAMAGE. 零件表面不得有缩松、气孔和裂纹等缺陷。表面清洁光亮，无损伤。6. THREAD HOLE INSERTS T

9、O WITHSTAND 1.5 TIMES RATED FASTENING TOQUE WITHOUT DAMAGE螺纹嵌件应该能够承受1.5倍的额定螺栓扭矩无损坏。7. UNSPECIFIED TOLEARANCE FOLLOW GB1148 OF CLASS MT5未注公差按照GB11486规定MT5级MAHINING PARTS机加工件:1. FILLET TO BE C_ UNLESS OTHERWISE SPECIFIED未注倒角C_2. RADII TO BE R_ UNLESS OTHERWISE SPECIFIED 未注圆角R_3. REMOVE ALL SHARP EDGES

10、 AND CORNERS 去除毛刺锐边4. FINISH: Fe/Zn_ /D (GB/T 9799, ISO20811)表面处理：Fe/Zn_ /D (GB/T 9799, ISO20811)II. MATERIALS材料规范SpecificationDescription0.75，1.5，2，2.5mm thick mm Al-Zn ALLOY COATED STEEL SHEET DX51D+AZ (GB14978)， mm 敷铝锌板 DX51D+AZ (GB14978)4， 5， 6， 8 mm thick mm HOT ROLLED STEEL SHEET (GB/T710), 2m

11、m 热轧钢板 (GB710)1.5，2， 2.5， 3mm thick mm COLD ROLLED STEEL SHEET Q235A (GB700), mm 冷轧钢板 Q235A (GB700)1.5， 2， 2.5，3， 4 mm thick mm STAINLESS STEEL SHEET 12Cr18Ni9 (GB20878), mm 不锈钢板 12Cr18Ni9 (GB20878)3X40, 4X40,4X60, 5X35, 5X50, 5X60, 5X80, 5X100; 6X30, 6X40, 6X50, 6X80, 6X100, 6X140, 8X40, 8X50, 8X80

12、, 8X60,8X120,8X100,10X40,10X50,10X120,10X80, 10X100, 10X125,12X80, 12X120, 12X150, 15X80, 15X100, 15X120, 15X150TMQY FULL ROUND BUSBAR(GB/5585.1), TMQY 全圆铜母排(GB/5585.1)3X25, 3X30, 4X60,5X30,5X40，6X20， 6X30， 6X40， 6X50， 6X60， 6X100， 6X120， 8X25， 8X40， 8X50， 8X60， 8X100，8X120，10X160，10X30， 10X40，10X50

13、， 10X60， 10X63，10X80， 10X100，10X120， 10X125，10X160， 12X120TMBY ROUND EDGE BUSBAR(GB/5585.1)，TMBY 圆角铜母排(GB/5585.1) HEXAGON STEEL BAR (GB699), 六角钢(GB699) ROUND STEEL BAR （GB699）, 圆钢 （GB699） ROUND COPPER BAR T2 GB5231， 圆铜棒T2 GB5231III. STANDARD HARDWARES标准件： SpecificationDescriptionEquivalent Internati

14、onal standardComment1GB5782HEXAGON HEAD BOLTISO40142GB80 HEXAGON SOCKET CONICAL POINT SET SCREWSISO40293GB5783 HEXAGON HEAD BOLTISO40174GB70.1HEXAGON SOCKET CAP SCREWSISO47625GB818 PAN HEAD SCREWS WITH CROSS RECESSEDISO70456GB77HEXAGON SOCKET SET SCREWS WITH FALT POINTISO40267GB6SLOTTED CHEESE HEAD

15、SCREWSISO12078GB953DOUBLE END STUDS9GB6170HEXAGON NUTSISO403210GB93SPRING LOCK WASHERSISO708911GB12618 ? *.1BLIND RIVETISO1597712GB97.1 PLAIN WASHERISO708913GB894.1 SNAP RINGISO40114GB801CARRIAGE BOLTISO867815DK- 4，5，6，8，10，12，14，16SNAP RING16NFE25-511-SKGRIP WASHERNFE25-511-SK17GB6560THREAD FORMING

16、 TAPPING SCREWS18GB70.3HEX SOCKET COUNTERSUNK HEAD SCREWSISO799119GB819.1CROSS RECESSED COUNTERSUNK HEAD SCREWSISO704620GB879.1SPRING ROLL PINISO875221GB91COTTER PINISO1234ITEM 16 GRIP WASHER AS FOLLOWS: ITEM 15 SNAP RING AS FOLLOWS: IV. TERMINOLOGYS术语OUTER LAYER 外层INNER LAYER 内层COUNTERSINK 沉孔SECTION 剖面DIRECTION 方向EMBOSS凸台SQUARE CUTOUT方孔SLOTTED HOLE 腰圆孔KNOCK-OFF HOLES敲落孔SMOO