车身和底盘支架排气系统的支架

1、Body Brackets and ChassisBrackets for Exhaust System 车身和底盘支架排气系统的支架1 Introduction 1.1 Scope. This General Specification contains the general requirements and associated tests regarding body brackets and chassis brackets for exhaust systems.1 说明 1.1范围。这个一般规格包括总体要求及有关车身和底盘的排气系统的相关检测。1.2 Mission / Them

2、e. The body brackets and chassis brackets serve the purpose of fastening the exhaust system to the underbody.1.2使命/主图。车体的支架和底盘支架的目的是紧固服务排气系统的底部。1.3 Classification. Not applicable.Note: Nothing in the specification supersedes applicable laws and regulations.Note: In the event of a conflict between th

3、e German and the English language, the German language shall take precedence.1.3分类。不适用。注意：在规范中没有可取代法律和法规。注意：在德和英语之间的冲突事件中，德语应优先考虑。2 References2 参考文献Note: Only the latest approved standards are applicable unless otherwise specified.注意：只有最新批准的标准适用除非另有规定。2.1 External Standards/Specifications. None.2.1外

4、部标准/产品规格。没有。2.2 GM Group Standards/Specifications.GME 08213吉密08213GME 08215吉密08215GME L-8C-2吉密L-8C-2GMW3059 GMW3059QT 001130 QT间期001130QT 001131 QT间期0011312.2 通用汽车集团标准/规格。吉密08213吉密08215吉密L-8C-2GMW3059QT间期001130QT间期0011312.3 Additional References. Relevant part drawings. 2.3其他参考资料。有关部分图纸。3 Test Prepa

5、ration and Evaluation 3 测试的制备与评价3.1 Resources. According to the relevant test procedures.3.1资源。据相关的测试程序。 Calibration. The test facilities and equipment shall be in good working order and shall have a valid calibration label.校准。设备和仪器的测试应当处于良好的工作秩序，并且有一个有效的校准标签。lternatives. Alternative test facilities

6、 and equipment may also be used. However, all measuring variables as specified in this specification shall be determined correctly with respect to its physical definition.替代品。也可以使用替代试验设施和设备。然而，在本规范中所有测量变量应正确地确定它的物理定义。 Facilities. According to the relevant test procedures.设施。根据有关测试程序。 Equipment. Acco

7、rding to the relevant test procedures.设备。根据有关测试程序。3.2 Test Samples. According to the relevant test procedures.The brackets shall be fastened to the vehicle floorpanel/chassis panel cutout as specified in the partdrawing.3.2 试验样品。根据相关的测试程序。支架应固定在车地板面板/机箱面板开孔中规定的部分绘图。3.3 Conditioning. According to the

8、 relevant test procedures.3.3空调。根据有关测试程序3.4 Documentation. Samples of components or material released to this specification shall be tested for conformity with the requirements of this specification and approved by the responsible GMDepartment prior to the start of delivery of production level compo

9、nents or materials.Any change to the component or material e.g. design, function, properties, manufacturing process and/or location of manufacture requires a new release of the product. It is the sole responsibility of the supplier to provide the customer, unsolicited, with documentation of any chan

10、ge or modification to the product/process, and to apply for a new release.If not otherwise agreed to the entire verification test shall be repeated and documented by the supplier prior to start of delivery of the modified or changed product. In some cases a shorter test can be agreed to between the

11、responsible GM Department and the supplier.3.4公文。本规范材料中组成或释放样品的部分应符合性测试的要求与本负责规范和总经理批准署前交货的生产开始级组件或材料。 任何组件或材料，例如设计变更，功能，性能，制造工艺和/或生产地点需要一个该产品的新版本。这是供应商提供客户唯一与文件的任何变动或修改，产品/工艺，并申请新的版本的责任，使顾客不请自来，。 如果不是另有约定到整个验证测试应重复记录和供应商交付的修改或变更产品。在某些短期测试情况下，可以使通用汽车公司和供应商之间达成协议。 Test Results. The test results shall

12、 be compiled in a test report.3.41测试结果。试验结果应编制在测试报告。 Deviations from Test Procedure. Deviations from the requirements of the test procedures shall have been agreed upon. Such requirements shall be specified on component drawings, test certificates, reports etc.偏差的试验程序。偏差的测试程序的要求应当已经商定。这种要求应当被指定在零件图，

13、测试证书，报告等中。4 Requirements and Test Procedure4 测试程序的要求4.1 Dimensioning. The dimensioning andarrangement of the brackets shall be according to GME 08215.For component and assembly dimensions, see part drawing.4.1标注。应按照吉密08215的尺寸和支架内安排的。对于组件和装配尺寸，见第一部分绘图。4.2 Strength Test. See GME L-8C-2. 4.2强度试验。见吉密L-8

14、C- 2型。4.3 Stress Measurement. See GME 08213.4.3压力测量。见吉密08213。4.4 Corrosion Test. The corrosion resistance shall be determined according to the material requirements.Requirement: See part drawing 4.4腐蚀试验。应根据的物质条件确定耐腐蚀性能。要求：见零件图4.5 Material Testing. 4.5材料测试 Materials. See part drawing.材料。见零件图。 Testing

15、 of Welded Joints. Pressure welded joints according to QT 001130.Fusion welded joints according to QT 001131. Requirement: The welded joints shall be performed according to QT 001130 and QT 001131 respectively. For additional requirements, see part drawing. 检验焊接接头。根据QT间期001130焊接压力接头。根据QT间期001131熔焊接头。要求：焊接接头应分别依据QT间和QT 001131 001130。要求看对于额外的零件图。5 Additio