安刻牌玻璃刻绘机手持键盘(手柄)英文使用说明

1、 Manual of Artcut Software Keyboard OperationsKeys on the Keyboard and Their Functions1. Process: With this key pressed, you can start processing after the origin is set under the Coordinate state.2. Pause/Continue: With this key pushed down during your processing, the machine will stop operating. C

2、lick on this key again, the machine will work again.3. Upper Right (XY): it makes X and Y axes move towards your upper right direction along an oblique line simultaneously.4. Forwards (Y): it makes the Y axis move forwards.5. Upper Left (XY): it makes X and Y axes move towards your upper left direct

3、ion along an oblique line.Right (X): with the key pushed down, the X axis moves to the right.7. Reset (X&Y): it will reset the X and Y coordinates. This key can be used for the adjustment of parameter values.8. Left (X): it makes the X axis move to the left.9. Lower Right (XY): with this key pressed

4、, the X and Y axes will move towards the lower right side along an oblique line.10. Backwards (X): this key moves the Y axis backwards.11. Lower Left (XY): it moves X and Y axes to the lower left along an oblique line.12. Changeover: it changes over the coordinates among RX, AX and OX. 13. Main Spin

5、dle: it is used to set the spindle switch, driving the spindle to rotate or stop operation.14. Move Set: it is used to set all move modes and parameters.15. Region: it is arranged for the setting of processing region.16. Tool Adjustment: with this key pressed, several options for the tool will be di

6、splayed on the screen where you can choose and adjust the tool position.17. Home: it makes all coordinates return to the absolute origin.18. OK: with this key clicked on, you can confirm and save all modification.19. Cancel: it is used to cancel all modification.20. Up (Z): it makes the Z axis move

7、up.21. Menu: it is a main menu from which you can find all required Setting items.22. Reset (Z): with this key pushed down, all Z coordinates will be reset.23. Repeat: you can repeat your operations.24. Down (Z): it makes the Z axis moves down.25. Edit: With this key, you can input all values after

8、the Parameter Set key is pushed down under the Coordinate state.26. Load Origin: it is used to call in a saved origin. With the Origin Call-in key pressed, select the origin number you need and call out the saved origin with the key OK pushed down after entering into the File status (It is unnecessa

9、ry to set the origin each time before the processing. With this method, you can call the saved origin, especially for the repetitive processing). 27. Save Origin: it is designed to save the set origin.28. Information: after making a click on this key, you can check the information in the file.Open t

10、he file you want to output, and then, A. Under the Display status, select the file you want to check.B. With the Open key pushed down, the Width (X-axis value) and Height (Y- axis value) of the file will be displayed.29. Setting: you can set all parameters such as Language options (Chinese, Unsimpli

11、fied or English)Chapter 2 Liquid Display InterfaceThere are two display statuses designed for the liquid display interface.1. File: under this status, you can display all files in the control system. With the proper key on the control keyboard pushed down, you can carry out the file operation.2. Coo

12、rdinate: under this status, you can display the current coordinate position. With the proper key pushed down on the control keyboard, you can move and locate the position of the tool holder for processing.Chapter 3 Function List. FileSelectAfter entering into the File status, press the key Y-Up or Y

13、-Down on the keyboard to select the file you need or Z-Up or Z-Down for turning to a fresh page.Delete 1) Direct DeleteA. When the hand-hold keyboard is operating under the status of Display file, push down the key Up (Y) or Down (Y) to select the file you need.B. With the key PAUSE pressed, there w

14、ill be a question Are you sure to delete the selected file? displayed on the screen. Then, you can click on the key ENTER to delete the selected file.2) Delete through Menu OptionsA. When the hand-hold keyboard is under the Display file status, push down the key UP(Y) or Down (Y) to select the file,

15、 followed by a click on the key Menu.B. After your pressing the key 4/ and selecting the option 4. Delete, the question of Are you sure to delete the selected file? will be displayed on the screen. Then, you can make a click on the key Enter to delete the selected file.3. FormatA. When the file is d

16、isplayed on the machine, press the key 3/Menu and get access to the Select column; and then, click on the option 2/Load or the key UP(Y)” or “Down (Y) to make a selection. After that, with the key Enter pushed down, the Format options appear on the liquid display, where you can push down the numeric

17、al keys 1 to 3 or the key UP(Y)” or “Down (Y) to select the proper mode. B. Push down the key OK again, the machine starts the Format process (Note: it is impossible to exit when the operation Format is in progress once the process begins).4. Update You can copy the update program to a USB disk or t

18、ransfer it to the controller, and then, push down the key MENU to make a selection between different items.A. Update main program B. Upgrade keyboard5. Main spindle: this option is designed to open or close the main spindle,Under Coordinate status, the main spindle will be changed from the status of

19、 ON to OFF with the key 7/Main Spindle pressed.6. Keyboard Language SelectionUnder Coordinate status, the keyboard adjustment interface will be displayed with the key 6/Setting pushed down. PositioningMoveAfter getting in Coordinate status, you can switch between Rapid, Click-and-Move and Slow statu

20、ses with the key 1/Move pushed down. With the key OK pressed, you can set the moving parameters for each status.Also, you can set the parameters for Rapid, Click-and-Move and Slow directly, with the key 6/Setting.2. Fine AdjustmentAfter entering into Coordinate status, push down the key Menu and the

21、n the key 1/Move or UP(Y)” or “Down (Y) to select the option Fine Adjustment. After that, press the key ENTER and get into the Adjustment interface. At this time, you can push down the key UP (Z) or “Down (Z), or make a click on the key OK and then input data directly for adjustment.3. Positioning:

22、moving to the point with absolute coordinatesAfter entering Coordinate status, push down the key Menu and then the key 2/Load or Up (Y) or “Down (Y)” to select the option Positioning. After that, press the key OK to get access to the Adjustment interface. At this time, you can push down the key UP(Z

23、) or “Down (Z)”, or make a click on the key OK again and then input data directly for adjustment.4. CalibrationAfter entering into Coordinate status, push down the key Menu and then the key 3/Menu, or choose the operation Calibration with the key “UP (Y)” or “Down(Y)” pushed down. After that, press

24、the key OK to enter into the Adjustment interface. Then, click on the key 6/Setting for parameter setting. Following that, you can make a choice with the key “UP (Y)” or “Down (Y)”. Press the key OK and input data immediately for adjustment. 5. Determination of Center PositionUnder Coordinate status

25、, press the key Menu and choose the option 4/Coordinate. Then, click on the key OK to enter into the proper interface. Again, push down the key OK to save the position coordinates of the left point. Move the X or Y axis to the appropriate position and push down the key OK to save the coordinates of

26、the right position. Repeat the steps described above to determine the positions of top and bottom points. After these operations, you can obtain the correct center position.6. Save the OriginIf the coordinates of the origin need to be saved after they are confirmed, press the key 5/Save to enter int

27、o the interface of Save Origin. And then input the serial numbers to be saved, and click on the key Ok to save them. You can save 12 coordinates altogether. The sign * before the figure indicates that one appropriate coordinate has been saved successfully.7. Load OriginIf it is required to call in t

28、he saved Origin during the period of processing, press the key 2/Load, and then input the numeral symbols corresponding to stored coordinates under Coordinate status, followed by the operation of pushing down the key OK.8. BreakpointStart processing from the last breakpoint.9. Nearest pointStart pro

29、cessing from the point where the main axis stops and which is nearest to the processed object.10. Coordinate settingUnder the status of coordinate, click “4/coordinate” to switch among RX, AX and OX. Afterwards, you can set or modify its value by using the menu. Setting1. Mode setting: Set different

30、 parameters for various carving modes.Under coordinate status, press “3/Menu”, and then press “5/Save” or select “Mode setting” via Down (Y).Therere totally 4 carving modes:When the mode is determined, press “OK” to input values to be modified and select via pressing UP (Y) or Down (Y). 2. Layer set

31、tingUnder coordinate status, press “3/Menu”, and then press “6/Setting” or select “Layer setting” via Down (Y). Press “OK” to enter, then press “X Left, X Right” to select layer number or whether to process or pause, setting via “Up (Z)” and “Down (Z)”.When “Yes” being pressed for both “Process” and

32、 “Pause”, pause time has to be input ultimately, and the user should input the required pause time.3. Cycle setting: Its an option to be selected during cyclic process. The offsets of X and Y as well as interval between cycles can be set.Under coordinate status, press “3/Menu”, and then press “7/Pri

33、nciple axis” or select “Cycle setting” via Down (Y). Press “OK” to enter. 4. Parameter setting: Parameters being related to machine operation can be set. After entering into coordinate status, press “6/Setting” or press UP (Z) or Down (Z) to make modification and then press “OK”. Also required value

34、s can be input directly. Press “Cancel” to exit. There will appear prompt for whether to save. If so, select “1. Confirm” and press “OK”; or else, select “2. Cancel” and parameter will not be modified. Process1. Normal processAfter file transfer, select file to be processed by pressing “UP (Y) Down

35、(Y)”. Press “OK” to enter into coordinate status. Press “X left/right” or “Y left/right” to determine the location of the origin and press “5/Save” to save the origin. Then press “” button and select “1. New origin” to start processing;2. Pause and continueDuring processing, processing will pause if

36、 press, press again, the processing will continue;3. OutlineAn outline can be added to the object to be processed. Under coordinate status, press “Process” button, select “7/Outline”, then select whether to “open light” and relevant parameters in the popup dialog box. 4. Bulk copy5. CycleProcess an

37、object circularly. After entering into coordinate mode, press “3/Menu” to enter into setting option. Set cycle parameters and then “Enter”; Press “Process” button and select “6.Cycle”, the system will operate automatically according to the cycle number and interval set previously;6. Presetting cutte

38、r Before processing, the position of cutter should be determined. Enter into coordinate status, press”8/Cutter presetting”, there will appear 4 options:Presetting cutter:Surface measuring:Cutter length measuring:Thickness of cutter presetter:. Use of flash memory1. FormattingBefore using a new flash

39、 memory, formatting should be implemented first on PC. Then the flash memory can be operated. 2. Register of flash memoryInsert the flash memory into controller after the machine is turned on. Press “3/Menu”, move “UP (Y) Down (Y)” or “3” to select “3. Read flash memory”, then press “2” and select “

40、2. Register” to register the flash memory. Instruction about “Delete old files” and “Register new files” will display on the LCD. When “Total amount of files Flash memory” is displayed, it means the flash memory is successfully registered. 3. Transfer data to flash memoryInsert the registered flash

41、memory to PC via USB interface. Click icon and find the carving machine equipment to be used;（Note: If carving machine is connected at the same time, two groups of carving machine parameters, such as names and models, will appear.）After click “OK”, interface of “Carving machine console” will pop up;In “File management” option, VRG file is the