现代有卡说明书

1、前沿非常感谢您使用本公司产品。本手册介绍了本产品的功能特点、安装调试步骤、操作等。提出了因操作不当可能引起的意外事故及常见故障的排除方法和使用注意事项。在使用本产品前，请先仔细阅读本说明书，以达到最佳使用效果。请妥善保存说明书并交最终使用者认真阅读现代机械制造2014 年 9 月现代有卡旋切机特点：刀具锋利，旋切精度高，刀片耐磨，装卡牢固，该机型有自动压杆和自动调刀装置，不用人工压杆，不脱刀，不蹦轴，并可自动调整刀高，压尺可向后翻转使刃磨刀具更加安全，方便，旋切出的单板平整度。均匀度、光滑度均达到国际标准，剩余木轴圆滑，粗细一致，该机旋切速度快，质量好，对操作要求低，节约木材，减少浪费，经济高

2、效。一、机床的主要技术参数1、旋切刀的长度：2700mm2、压尺长度：2730mm3、旋切圆木最大长度：2600mm4、旋切圆木最大直径：1500mm5、旋切后圆木最小直径：120mm6 主轴转速：10-75rpm7、机床最大外形尺寸（长宽高）： 6000mm2250mm2300mm8、刀架快速移动速度：1120mm/min9、配用电机功率：（1）主电机：调速电机 YCT250-4B22KW夹紧电机：Y112M-4进给电机：Y112M-6小吊具电机：Y112M-44KW1.5KW3KW（5）数控进给电机：Y112M-410、机床总重量：约 7 吨2.2KW二、机床的吊运本机床吊运时，应确保安全

3、，按规定位置起吊，不得碰伤加工表面和油漆表面。三、机床的安装本机床应安装在平整的水泥地面上，要求地础牢固，机床安放后，应找平机架，机床使用时应稳固可靠，必要时可以安装地脚螺栓紧固。四、机床的调整及使用1、刀片的刃磨的角度 2122，如果旋切刀的厚度为 12.7mm，刃磨部分的宽度为 34mm 左右，刀片磨好后，必须用油石光刀刃。2、刀片安装应以主轴中心水平高度为准，两端高度必须完全一致。（刀刃至导轨上平面的距离为 165mm）3、校正压尺棱与刀刃的平行度，并调整到理想的范围。4、旋切过程中如出现脱刀（1）刀的高度太高，也可按调刀的上升按钮，适当调节刀台的角度。（2）压尺棱与刀刃的平行度不好。5

4、、旋切过程中如出现蹦刀刀的高度太低，也可按调刀的下降按钮，小导轨的后面的高度不能低于前端的高度。五、机床的润滑和1、新设备使用前必须将主电速箱加机油 10 升左右。2、小吊车上的 2 个机，每个加机油 2 升左右。3、站内加油（有油标）4、所有链条、链轮、丝杠、丝母都应每班加机油或黄油润滑。5、各运动旋转部位每班加润滑油一次。六、设备数控调整1、机械进给时，齿轮每个齿数的厚度为 0.875mm，例如旋切 0.30mm 的板皮，300.875=34，用 34 齿的齿轮即可。2、数控进给时，挂轮架用 54 齿的齿轮，如果屏幕上调刀 30.00 旋切后，板皮的实际厚度为 0.32mm，调节方法如下：

5、按向右的箭头，屏幕最下端出现厚度系数，数字为黑色的130.0%，按 SET，让黑色，（旋切后的实际厚度 32 除以屏幕上的 30 等于 1.066，用它乘以厚度系数 130.0%，得数为138.7%），按向上的家头调到 138.7%，按绿色 ENT 键，再按红色的 ESC 键退出即可。nk you very much for the use of the companys products.This manual describes the functions, the product installation anddebugging steps, etc. The accidentwas

6、causedbythe improperoperation and common troubleshooting methods and matters needingattention.Before using this product, please read this manual carefully, inorder to achieve the best results.Please keep this manual anduser to readThe Xiandai machinery manufacturing Co.,.2014 SeptemberThe front edge

7、Modern cardpeelingmachine, themachine tool issharp, cuttingpreci, toolwear, cled firmly, thems haveautomatic prerebar and automatictoolsetting device, withoutmanual prerebar, noknife, donot skip shaft, andcanautomatically adjustthecutterheight,prere gaugecan flipback to grinding the tool is more saf

8、e,convenient, veneer of smoothness.Evenness, smoothness areuptoernationalstandards, theremaining wood shaft smooth, uniformthickness, the cutting speed, goodquality, lowrequirementsforoperators,woodsaving, wastereduction, economic efficiency.One,The maechnical parameters, machine tool1, rotary cutte

9、r length: 2700mm2, prere gauge length: 2730mm3, theum length of rotary cutting logs: 2600mm4, peeling logum diameter: diameter 1500mm5, afteeling log minimum diameter: diameter 120mm6 spindle speed: 10-75rpm7,um size (length * width * height):6000mm * 2250mm * 2300mm8, Fast moving speed, tool: 1120m

10、m/min9, motorer:(1) the maotor: motor YCT250-4B 22KW(2) the cling motor: Y112M-4 4KW(3) the feed motor: Y112M-6 1.5KW(4) small lifting motor: Y112M-4 3KW(5) the CNC feed motor: Y112M-4 2.2KW10, the total weight of about 7 tons of machine tools:Two, machine tool liftingThis machine is hoisted, shall

11、ensure the safety,itionin accordancewith the provis of lifting, not hurt the machined surface and pasurface.Three, the installation of machine toolsThe machine should be installed on flat cement on the ground, thefoundation base, machinetool shouldbe placed after leveling, frame,machine tool use sho

12、uld be stable and reliable, it may be nesary toinstall theanchor bolts fastening.Four, adjust and use of machine tools1, the blade sharpening angle of 21 - 22 rotary cutter, if the thicknessof 12.7mm, the grinding part of the width isabout34mm, the bladesharpening, must use oil stone light blade.2,

13、theblade shouldbeinstalledhespindlecenter level level, heightmustbecompleyconsistent. (edge to guide plane distance is 165mm)3, the correction prere bar edge and edge paralleldegree, and adjustto the ideal range.4, rotary cutting proch as knife(1) the knife height is too high, can also according to

14、the ascendingbutton adjustable knife, knife angle adjusting.(2) prere bar edge and edge parallel degree is not good.5, rotary cutting jump knife such as prosKnife heightistoolow, itcanalsobe adjustable knife downbutton,behind the small rail height of not lessn the height of front end.Five, machine t

15、ool lubrication and maenance1, the new equipment must be the maotor and gearbox oil 10 liters.2 speed reducer 2, small crane, each with 2 liters of oil.3 hydraulic sion, hydraulic oil (oil standard)4, all the chain, sprocket, screw, nut should each of his oilrease.5, the movement of the roing parts

16、of every class lubricating oil a.Six, CNC equipment adjustment1, mechanical feed gear numberofteeth, each thicknessof0.875mm,such as rotary cutting 0.30mm plate, 30 / 0.875=34, with 34teeth gear can.2, CNCFeed, hangingwheelframe with the54gear, ifthescreen up-regulated afterrotarycutting knife 30, theactual thicknessof slab0.32mm, regulating methods are as follows: according to the rightarrow, atthebottomendof thethicknesscoefficient screen appears,digital black 130%, according to SET, let fadeto black, (