ansysworkbench7.1培训幻灯DS7_ch01_Intro.ppt

1、DesignSpace 7.0,Training Manual,Inventory Number: 001759 First Edition DesignSpace Release: 7.0 Published Date: October 25, 2002 Registered Trademarks: ANSYS is a registered trademark of SAS IP Inc. All other product names mentioned in this manual are trademarks or registered trademarks of their res

2、pective manufacturers. Disclaimer Notice: This document has been reviewed and approved in accordance with the ANSYS, Inc. Documentation Review and Approval Procedures. “This ANSYS Inc. software product (the Program) and program documentation (Documentation) are furnished by ANSYS, Inc. under an ANSY

3、S Software License Agreement that contains provisions concerning non-disclosure, copying, length and nature of use, warranties, disclaimers and remedies, and other provisions. The Program and Documentation may be used or copied only in accordance with the terms of that License Agreement.” Copyright

4、2002 SAS IP, Inc. Proprietary data. Unauthorized use, distribution, or duplication is prohibited. All Rights Reserved.,Training ManualDesignSpace 7.0,October 25, 2002 Inventory # 001759 1-3,DesignSpace Training Outline,Chapter 1: Introduction Chapter 2: The DesignSpace GUI Chapter 3: Using DesignSpa

5、ce Chapter 4: Assemblies and Contact Chapter 5: Controlling Accuracy - Convergence and Scoping Chapter 6: Design Studies and Parameters,Chapter 7: DesignSpace Report Chapter 8: DesignSpace Customization, Control Panel and Variable Manager Chapter 9: DesignSpace Advanced Options Appendix: 1: Advanced

6、 Controls 2: Fatigue,Introduction,Chapter 1,October 25, 2002 Inventory # 001759 1-6,Introduction,Chapter 1 Contents: Product Configurations Hardware support Licensing Geometry Plugins and Readers DesignSpace Disciplines in Brief DesignSpace to ANSYS Geometry and Meshing Simulation Wizard Demonstrati

7、on,October 25, 2002 Inventory # 001759 1-7,DesignSpace Product Configurations,DesignSpace Scalability: Product determines available features (see below). Product configuration is controlled by licensing. Add-in availability is license controlled.,October 25, 2002 Inventory # 001759 1-8,DesignSpace O

8、S/Hardware Support,Windows NT4 (SP 5 or SP 6): Solver supports multiple processors. Windows XP (Home or Professional) Solver supports multiple processors. Windows 2000: Solver supports multiple processors. Windows ME Unix support to come after initial release. Additional Requirements: MS Internet Ex

9、plorer v5.5 or higher (available ). 800 x600 minimum video resolution. Minimum 65536 colors.,October 25, 2002 Inventory # 001759 1-9,DesignSpace Licensing,License Manager: FLEXlm used for all ANSYS products. All products will use a single, common license manager and license directory. Floating licen

10、se capability. Multiple configuration capability: Example Site could have a few Optima licenses, and many Entra. DesignSpace launcher allows license selection at start up.,October 25, 2002 Inventory # 001759 1-10,Geometry Plug-Ins and Readers,Associative (Plug-In): Inventor R5, R5.3 Mechanical Deskt

11、op (5.0 or 6.0) Pro/ENGINEER 2000i2 or 2001 Solid Edge v11 and 12 SolidWorks 2001, 2001+ Unigraphics (V17 and 18) Non-Associative (Reader): ACIS (8.0) CATIA (v 4 and 5) Inventor (R4) Parasolid (14.0) Unigraphics (16.0.3.3 or 17.0) AGP 7.x XML,October 25, 2002 Inventory # 001759 1-11,DesignSpace Disc

12、iplines - In Brief,Stress: Determines deflections, stresses, factor of safety, etc. based on standard strength of materials concepts. Thermal: Static thermal analyses. Temperature-dependent conductivity and convection supported. Modal: Determines natural frequencies of a solid body. Specify number o

13、f modes and/or frequency range. Buckling Determine failure load or safety factor for buckling. View buckled shape to understand failure mechanism.,October 25, 2002 Inventory # 001759 1-12,DesignSpace Disciplines - In Brief,Coupled Field Problems: Thermal/Stress: Calculates thermally induced stresses

14、 and deflections. Modal/Stress: Calculates natural frequency based on prestressed structure. Shape: Indicates areas of possible volume reduction based on load paths through the part using Topological Optimization technology.,October 25, 2002 Inventory # 001759 1-13,DesignSpace to ANSYS,Availability

15、dependent upon product configuration. Gateway to ANSYS for work beyond capabilities of DesignSpace. Templates: Ansys input file (*.INP) Export ANSYS database file (*.DB),October 25, 2002 Inventory # 001759 1-14,Geometry and Meshing,DesignSpace 6.0 supports two types of geometry,Solids All CAD format

16、s Parts or Assemblies,Surfaces or sheets (shell elements): Unigraphics, Solid Works, Pro-Engineer, ACIS and Parasolid. Parts only or solid/surface assembly.,October 25, 2002 Inventory # 001759 1-15,Simulation Wizard,The Simulation Wizard provides a step-by-step process for creating a simulation envi

17、ronment and getting results - Fast! Check list format with highlighted fields and callout boxes: Learning tool for new user. Reference tool for occasional user. Covered fully in chapter 2.,October 25, 2002 Inventory # 001759 1-16,Want More Practice?,The DesignSpace CD includes a number of sample par

18、ts: x:Samples . . . (where x is CD drive letter). Subdirectories contain geometry models in neutral file formats as well as CAD specific formats. After becoming familiar with the Simulation Wizard and this course you should be able to use any of the sample files to practice simulation techniques.,October 25, 2002 Inventory # 001759 1-17,Start the Simulation Wizard from screen menu or toolbar. Instructor will demonstrate various DesignSpace capabilities by using the Simulation Wizard to evaluate the surface model shown on next page.,Demo