人人文库网 > 图纸下载 > 毕业设计 > 应急灯外壳注塑模具设计【8张CAD图纸和说明书】

翻译原文改.pdf

应急灯外壳注塑模具设计【8张CAD图纸和说明书】

资源目录

应急灯外壳注塑模具设计【8张CAD图纸和说明书】.rar

毕业设计中期检查表.doc---(点击预览)

毕业设计(论文)开题报告.doc---(点击预览)

应急灯外壳注塑模具设计任务书.doc---(点击预览)

CAXA图纸

型腔板A1.exb

复位杆A2.exb

定位圈A2.exb

带肩导套A2.exb

应急灯塑件图A1.exb

应急灯模具装配图A0.exb

支撑块A2.exb

顶杆A2.exb

型腔板A1.dwg

复位杆A2.dwg

定位圈A2.dwg

带肩导套A2.dwg

应急灯塑件图A1.dwg

应急灯模具装配图A0.dwg

支撑块A2.dwg

顶杆A2.dwg

压缩包内文档预览：

编号：10118841 类型：共享资源大小：7.84MB 格式：RAR 上传时间：2018-05-23 上传人：俊****计 IP属地：江苏

40
积分

版权申诉 word格式文档无特别注明外均可编辑修改；预览文档经过压缩，下载后原文更清晰！ 立即下载

关键词：: 应急灯外壳注塑模具设计 cad 图纸以及说明书仿单

资源描述：

摘要

本论文主要研究的是应急灯外壳注塑模具的设计方法。本文首先介绍了选题的依据以及选这个课题的意义，并简单介绍了注塑模具的发展现状。然后分析了应急灯外壳制件的工艺特点，包括结构工艺性、成型特性与条件、材料性能等，并选定了成型设备。接着述说了应急灯外壳注塑模的分型面选择、模具基本结构及模架的选定及型腔数目的选定及布置，重点论述了成型零件、浇注系统、、脱模机构、合模导向机构以及冷却系统的设计。而后选定标准模架和模具材料，并校核注射机的相关工艺参数，如最大注射量、注塑压力等。最后阐述模具的工作原理，以及对安装运行过程中可能出现的问题予以总结、分析，并给于了对应的解决方法。

本文论述的应急灯外壳注塑模具采用两板式结构，采用一模两腔的型腔布置，最后通过推板将制件推出。在设计模具的时候，需用到SoliWorks软件进行模拟，以确定型芯型腔及浇口位。此次应急灯外壳注塑模具的设计各项参数必须来源可靠、选择准确、计算无误，其中最大注射量及注射压力是计算的关键。在工艺性上保证不影响操作的同时尽量做到了加工操作简单、方便。

本设计是在传统的应急灯上进行了创新，设计采用最领先技术LED显示，并把电池装在灯内部，外部也更美观。外壳的尺寸大小适中，模架也较好的选择，模具整体不大，采用整体安装。

关键词：应急灯外壳；注塑模；两板模；浇注系统；脱模机构

Abstract

The designing methods of injection mould of the Emergency light shell are mainly introduced in this paper. This paper introduces the topic basis and the significance of choosing thistopic, and briefly introduces the development status of injection mold.And then analyzes the process characteristics of emergency lamp shellparts, including the structure, characteristics and conditions of moldingprocess, material properties, and select the molding equipment.Then tell the type emergency lamp shell injection mold, mold surfacestructure and mold base selection and the number of cavities selection andlayout, emphasis, gating system, forming parts, demoulding mechanism,clamping mechanism and the cooling system design.Finally the selected standard mold and mold material, and process parameters of injection machine check, such as the maximum injection volume, injection pressure etc.. The working principle of the die, as well as to the possible problems in the process of installation and operation are summarized, analysis, and give the corresponding solutions.

Shell of emergency lamp injection mold in this paper adopts two plate structure, the layout of the cavity of a mould with two cavities, the push platewill work out.In the design of mold, use the SoliWorks software to simulate, in order to determine the core and cavity and runner position.Must choose accurate, reliable, accurate calculation of design parameters of the emergency lamp shell injection mold, the largest injection quantityand injection pressure is the key.In the process that does not affect the operation at the same time as far as possible the process has the advantages of simple operation, convenient.

This design is the innovation in the emergency lights on the traditionaldesign, using the most advanced technology of LED display, and the battery installed in the light of internal, external and more beautiful.Moderate size of shell mold, is the better choice, overall not die, the wholeinstallation.

Keyword: Emergency light shell;Injection mould;Threepence mould;Gating system;Moulding mechanism ; Space parting institutions

引言 1

第1章应急灯外壳工艺性分析 4

1.1 材料性能 4

1.2 成型特性和条件 4

1.3 结构工艺性 4

1.4 产品几何形状分析 5

1.5 应急灯外壳注塑工艺参数的确定 9

1.6 初选注射机的型号和规格 9

第2章应急灯外壳注塑模具的结构设计 11

2.1 分型面的选择 11

2.2 确定模具基本结构及模架的选定 12

2.3 确定型腔的数量和布局 12

2.4浇注系统设计 13

2.4.1主流道设计 13

2.4.2 分流道截面设计及布局 14

2.4.3 浇口设计及位置选择 15

2.4.4 浇口套的设计 16

2.5 注塑模成型零部件设计 17

2.5.1 成型零部件尺寸分析 17

2.5.2塑件收缩率的影响 17

2.5.3型腔、型芯结构设计 18

2.5.4 成型零件工作尺寸计算 20

2.6 合模导向机构设计 20

2.7 脱模、推出机构设计 21

2.7.1 推出机构的组成 21

2.7.2 推出机构的分类 21

2.7.3 推出机构的设计原则 21

2.8冷却系统设计 23

2.9 模架及模具材料的选择 24

第3章注射机相关参数校核 25

3.1 最大注射量的校核 25

3.2 注射压力校核 26

3.3 锁模力校核 26

3.4 模具厚度的校核 26

3.5 成型零部件强度校核计算 27

第4章模具的工作原理及安装、调试 28

4.1 模具的工作原理 28

4.2 模具的安装 29

4.3 试模 29

结论 31

谢辞 32

参考文献 33

引言

1.选题的依据及意义

随着现代制造技术及高新技术的迅速发展、计算机科技的应用，在工业中模具将要变成生产各种产品不可缺少的重要工艺装备。尤其是在塑料产品的制造和生产过程中，应用塑料模具相当广泛，在各类模具中的重要程度也越来越突显，成为一系列模具设计、制造与研究中最具有表现意义的模具之一。随着注塑模具不断成为生产塑料制造品的主要手段，且不断发展成为最有前景的模具之一。注射成型是现在市场上最具前景、最常用的塑料成型手段之一，因此注塑模具作为塑料模的一种，它将具有相当大的市场需求量。因此我选应急灯注塑模具设计作为我毕业设计选择的课题。

本课题知识点与涉及的知识面较多，应用性强与，如模具设计、三维造型、注塑成型、二维三维软件的应用以及运动仿真。

全部文件.png

应急灯塑件图A1.gif

应急灯模具装配图A0.gif

带肩导套A2.gif

顶杆A2.gif

定位圈A2.gif

复位杆A2.gif

型腔板A1.gif

支撑块A2.gif

内容简介：: Journal of Materials Processing Technology 171 (2006) 259267 Design and thermal analysis of plastic injection mould S.H. Tang , Y .M. Kong, S.M. Sapuan, R. Samin, S. Sulaiman Department of Mechanical and Manufacturing Engineering, Universiti Putra Malaysia, 43400 Serdang, Selangor, Malaysia Received 3 September 2004; accepted 21 June 2005 Abstract This paper presents the design of a plastic injection mould for producing warpage testing specimen and performing thermal analysis for the mould to access on the effect of thermal residual stress in the mould. The technique, theory, methods as well as consideration needed in designing of plastic injection mould are presented. Design of mould was carried out using commercial computer aided design software Unigraphics, Version 13.0. The model for thermal residual stress analysis due to uneven cooling of the specimen was developed and solved using a commercial nite element analysis software called LUSAS Analyst, Version 13.5. The software provides contour plot of temperature distribution for the model and also temperature variation through the plastic injection molding cycle by plotting time response curves. The results show that shrinkage is likely to occur in the region near the cooling channels as compared to other regions. This uneven cooling effect at different regions of mould contributed to warpage. 2005 Elsevier B.V . All rights reserved. Keywords: Plastic Injection mould; Design; Thermal analysis 1. Introduction Plastic industry is one of the worlds fastest growing industries, ranked as one of the few billion-dollar industries. Almost every product that is used in daily life involves the usage of plastic and most of these products can be produced by plastic injection molding method 1. Plastic injection molding process is well known as the manufacturing process to create products with various shapes and complex geometry at low cost 2. The plastic injection molding process is a cyclic process. There are four signicant stages in the process. These stages are lling, packing, cooling and ejection. The plastic injec- tion molding process begins with feeding the resin and the appropriate additives from the hopper to the heating/injection system of the injection plastic injection molding machine 3. This is the “lling stage” in which the mould cavity is lled with hot polymer melt at injection temperature. After the cav- ity is lled, in the “packing stage”, additional polymer melt is packed into the cavity at a higher pressure to compensate the expected shrinkage as the polymer solidies. This is followed Corresponding author. E-mail address: saihong.my (S.H. Tang). by “cooling stage” where the mould is cooled until the part is sufciently rigid to be ejected. The last step is the “ejection stage” in which the mould is opened and the part is ejected, after which the mould is closed again to begin the next cycle 4. The design and manufacture of injection molded poly- meric parts with desired properties is a costly process domi- nated by empiricism, including the repeated modication of actual tooling. Among the task of mould design, designing the mould specic supplementary geometry, usually on the core side, is quite complicated by the inclusion of projection and depression 5. In order to design a mould, many important designing factors must be taken into consideration. These factors are mould size, number of cavity, cavity layouts, runner systems, gating systems, shrinkage and ejection system 6. In thermal analysis of the mould, the main objective is to analyze the effect of thermal residual stress or molded-in stresses on product dimension. Thermally induced stresses develop principally during the cooling stage of an injection molded part, mainly as a consequence of its low thermal conductivity and the difference in temperature between the molten resin and the mould. An uneven temperature eld exists around product cavity during cooling 7. 0924-0136/$ see front matter 2005 Elsevier B.V . All rights reserved. doi:10.1016/j.jmatprotec.2005.06.075260 S.H. Tang et al. / Journal of Materials Processing Technology 171 (2006) 259267 During cooling, location near the cooling channel experi- ences more cooling than location far away from the cooling channel. This different temperature causes the material to experience differential shrinkage causing thermal stresses. Signicant thermal stress can cause warpage problem. There- fore, it is important to simulate the thermal residual stress eld of the injection-molded part during the cooling stage 8.By understanding the characteristics of thermal stress distribu- tion, deformation caused by the thermal residual stress can be predicted. In this paper the design of a plastic injection mould for producing warpage testing specimen and for performing ther- mal analysis for the mould to access on the effect of thermal residual stress in the mould is presented. 2. Methodology 2.1. Design of warpage testing specimen This section illustrates the design of the warpage testing specimen to be used in plastic injection mould. It is clear that warpage is the main problem that exists in product with thin shell feature. Therefore, the main purpose of the prod- uct development is to design a plastic part for determining the effective factors in the warpage problem of an injection- moulded part with a thin shell. The warpage testing specimen is developed from thin shell plastics. The overall dimensions of the specimen were 120 mm in length, 50 mm in width and 1 mm in thickness. The material used for producing the warpage testing specimen was acrylonitrile butadiene stylene (ABS) and the injection temperature, time and pressure were 210 C, 3 s and 60 MPa, respectively. Fig. 1 shows the warpage testing specimen pro- duced. 2.2. Design of plastic injection mould for warpage testing specimen This section describes the design aspects and other consid- erations involved in designing the mould to produce warpage testing specimen. The material used for producing the plastic Fig. 1. Warpage testing specimen produced. injection mould for warpage testing specimen was AISI 1050 carbon steel. Four design concepts had been considered in designing of the mould including: i. Three-plate mould (Concept 1) having two parting line with single cavity. Not applicable due to high cost. ii. Two-plate mould (Concept 2) having one parting line with single cavity without gating system. Not applicable due to low production quantity per injection. iii. Two-plate mould (Concept 3) having one parting line with double cavities with gating and ejection system. Not applicable as ejector pins might damage the product as the product is too thin. iv. Two-plate mould (Concept 4) having one parting line with double cavities with gating system, only used sprue puller act as ejector to avoid product damage during ejection. In designing of the mould for the warpage testing spec- imen, the fourth design concept had been applied. Various design considerations had been applied in the design. Firstly, the mould was designed based on the platen dimen- sion of the plastic injection machine used (BOY 22D). There is a limitation of the machine, which is the maximum area of machine platen is given by the distance between two tie bars. The distance between tie bars of the machine is 254 mm. Therefore, the maximum width of the mould plate should not exceed this distance. Furthermore, 4 mm space had been reserved between the two tie bars and the mould for mould setting-up and handling purposes. This gives the nal max- imum width of the mould as 250 mm. The standard mould base with 250 mm 250 mm is employed. The mould base is tted to the machine using Matex clamp at the upper right and lower left corner of the mould base or mould platen. Dimen- sions of other related mould plates are shown in Table 1. The mould had been designed with clamping pressure having clamping force higher than the internal cavity force (reaction force) to avoid ashing from happening. Based on the dimensions provided by standard mould set, the width and the height of the core plate are 200 and 250 mm, respectively. These dimensions enabled design of two cavities on core plate to be placed horizontally as there is enough space while the cavity plate is left empty and it is only xed with sprue bushing for the purpose of feeding molten plastics. Therefore, it is only one standard parting line was designed at Table 1 Mould plates dimensions. Components Size (mm) width height thickness Top clamping plate 250 250 25 Cavity plate 200 250 40 Core plate 200 250 40 Side plate/support plate 37 250 70 Ejector-retainer plate 120 250 15 Ejector plate 120 250 20 Bottom clamping plate 250 250 25S.H. Tang et al. / Journal of Materials Processing Technology 171 (2006) 259267 261 the surface of the product. The product and the runner were released in a plane through the parting line during mould opening. Standard or side gate was designed for this mould. The gate is located between the runner and the product. The bottom land of the gate was designed to have 20 slanting and has only 0.5 mm thickness for easy de-gating purpose. The gate was also designed to have 4 mm width and 0.5 mm thickness for the entrance of molten plastic. In the mould design, the parabolic cross section type of runner was selected as it has the advantage of simpler machin- ing in one mould half only, which is the core plate in this case. However, this type of runner has disadvantages such as more heat loss and scrap compared with circular cross section type. This might cause the molten plastic to solidify faster. This problem was reduced by designing in such a way that the runner is short and has larger diameter, which is 6 mm in diameter. It is important that the runner designed distributes material or molten plastic into cavities at the same time under the same pressure and with the same temperature. Due to this, the cavity layout had been designed in symmetrical form. Another design aspect that is taken into consideration was air vent design. The mating surface between the core plate and the cavity plate has very ne nishing in order to prevent ashing from taking place. However, this can cause air to trap in the cavity when the mould is closed and cause short shot or incomplete part. Sufcient air vent was designed to ensure that air trap can be released to avoid incomplete part from occurring. The cooling system was drilled along the length of the cavities and was located horizontally to the mould to allow even cooling. These cooling channels were drilled on both cavity and core plates. The cooling channels provided suf- cient cooling of the mould in the case of turbulent ow. Fig. 2 shows cavity layout with air vents and cooling channels on core plate. In this mould design, the ejection system only consists of the ejector retainer plate, sprue puller and also the ejector Fig. 2. Cavity layout with air vents and cooling channels. plate. The sprue puller located at the center of core plate not only functions as the puller to hold the product in position when the mould is opened but it also acts as ejector to push the product out of the mould during ejection stage. No addi- tional ejector is used or located at product cavities because the product produced is very thin, i.e. 1 mm. Additional ejec- tor in the product cavity area might create hole and damage to the product during ejection. Finally, enough tolerance of dimensions is given consid- eration to compensate for shrinkage of materials. Fig. 3 shows 3D solid modeling as well as the wireframe modeling of the mould developed using Unigraphics. 3. Results and discussion 3.1. Results of product production and modication From the mould designed and fabricated, the warpage testing specimens produced have some defects during trial run. The defects are short shot, ashing and warpage. The short shot is subsequently eliminated by milling of additional air vents at corners of the cavities to allow air trapped to Fig. 3. 3D solid modeling and wireframe modeling of the mould.262 S.H. Tang et al. / Journal of Materials Processing Technology 171 (2006) 259267 Fig. 4. Extra air vents to avoid short shot. escape. Meanwhile, ashing was reduced by reducing the packing pressure of the machine. Warpage can be controlled by controlling various parameters such as the injection time, injection temperature and melting temperature. After these modications, the mould produced high qual- ity warpage testing specimen with low cost and required little nishing by de-gating. Fig. 4 shows modications of the mould, which is machining of extra air vents that can eliminate short shot. 3.2. Detail analysis of mould and product After the mould and products were developed, the analysis of mould and the product was carried out. In the plastic injec- tion moulding process, molten ABS at 210 C is injected into the mould through the sprue bushing on the cavity plate and directed into the product cavity. After cooling takes place, the product is formed. One cycle of the product takes about 35 s including 20 s of cooling time. The material used for producing warpage testing speci- men was ABS and the injection temperature, time and pres- sure were 210 C, 3 s and 60 MPa respectively. The material selected for the mould was AISI 1050 carbon steel. Properties of these materials were important in determin- ing temperature distribution in the mould carried out using nite element analysis. Table 2 shows the properties for ABS and AISI 1050 carbon steel. The critical part of analysis for mould is on the cavity and core plate because these are the place where the product is formed. Therefore, thermal analysis to study the temperature Fig. 5. Model for thermal analysis. distribution and temperature at through different times are performed using commercial nite element analysis software called LUSAS Analyst, Version 13.5. A two-dimensional (2D) thermal analysis is carried out for to study the effect of thermal residual stress on the mould at different regions. Due to symmetry, the thermal analysis was performed by modeling only the top half of the vertical cross section or side view of both the cavity and core plate that were clamped together during injection. Fig. 5 shows the model of thermal analysis analyzed with irregular meshing. Modeling for the model also involves assigning properties and process or cycle time to the model. This allowed the nite element solver to analyze the mould modeled and plot time response graphs to show temperature variation over a certain duration and at different regions. For the product analysis, a two dimensional tensile stress analysis was carried using LUSAS Analyst, Version 13.5. Basically the product was loaded in tension on one end while the other end is clamped. Load increments were applied until the model reaches plasticity. Fig. 6 shows loaded model of the analysis. 3.3. Result and discussion for mould and product analysis For mould analysis, the thermal distribution at different time intervals was observed. Fig. 7 shows the 2D analysis Table 2 Material properties for mould and product Carbon Steel (AISI 1050), mould ABS Polymer, product Density, 7860 kg/m 3 Density, 1050 kg/m 3 Youngs modulus, E 208 GPa Youngs modulus, E 2.519 GPa Poissons ratio, 0.297 Poissons ratio, 0.4 Yield strength, S Y 365.4 MPa Yield strength, S Y 65 MPa Tensile strength, S UTS 636 MPa Thermal expansion, 65 10 6 K 1 Thermal expansion, 11.65 10 6 K 1 Conductivity, k 0.135 W/(m K) Conductivity, k 49.4 W/(m K) Specic heat, c 1250 J/(kg K) Specic heat, c 477 J/(kg K)S.H. Tang et al. / Journal of Materials Processing Technology 171 (2006) 259267 263 Fig. 6. Loaded model for analysis of product. contour plots of thermal or heat distribution at different time intervals in one complete cycle of plastic injection molding. For the 2D analysis of the mould, time response graphs are plotted to analyze the effect of thermal residual stress on the products. Fig. 8 shows nodes selected for plotting time response graphs. Figs. 917 show temperature distribution curves for dif- ferent nodes as indicated in Fig. 8. From the temperature distribution graphs plotted in Figs. 917, it is clear that every node selected for the graph plotted experiencing increased in temperature, i.e. from the ambient temperature to a certain temperature higher than the ambient temperature and then remained constant at this temperature for a certain period of time. This increase in tem- perature was caused by the injection of molten plastic into the cavity of the product. After a certain period of time, the temperature is then further increased to achieve the highest temperature and remained constant at that temperature. Increase in temper- ature was due to packing stages that involved high pressure, Fig. 7. Contour plots of heat distribution at different time intervals.264 S.H. Tang et al. / Journal of Materials Processing Technology 171 (2006) 259267 Fig. 8. Selected nodals near product region for time response graph plots. Fig. 9. Temperature distribution graph for Node 284. Fig. 10. Temperature distribution graph for Node 213. Fig. 11. Temperature distribution graph for Node 302. Fig. 12. Temperature distribution graph for Node 290. which caused the temperature to increase. This temperature remains constant until the cooling stage starts, which causes reduction in mould temperature to a lower value and remains at this value. The graphs plotted were not smooth due to the absence of function of inputting lling rate of the molten plastic as well as the cooling rate of the coolant. The graphs plotted only show maximum value of temperature that can be achieved in the cycle. The most critical stage in the thermal residual stress anal- ysis is during the cooling stage. This is because the cooling Fig. 13. Temperature distr

温馨提示:
1: 本站所有资源如无特殊说明，都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
2: 本站的文档不包含任何第三方提供的附件图纸等，如果需要附件，请联系上传者。文件的所有权益归上传用户所有。
3.本站RAR压缩包中若带图纸，网页内容里面会有图纸预览，若没有图纸预览就没有图纸。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 人人文库网仅提供信息存储空间，仅对用户上传内容的表现方式做保护处理，对用户上传分享的文档内容本身不做任何修改或编辑，并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容，请与我们联系，我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

人人文库网所有资源均是用户自行上传分享，仅供网友学习交流，未经上传用户书面授权，请勿作他用。