LT70001DHT-02不带TP规格书.doc

深圳亮晶晶电子有限公司SHENZHEN SPARKLING ELECTRONICS CO., LTD样品承认书Customer： Date：2011-04-217.0” 800*RGB*480 DOTSMODULE NO.: LT70001DIT-02 Customer ApprovedElectronic Mechanism Touch Panel Performance Performance PerformanceApproved QC Confirmed Designer备注：规格书一式三份，客户惠存两份，另一份请寄回亮晶晶公司业务接口人： 电话：公司地址：深圳市光明新区凤新路勒堡工业园1栋公司电话61537032 传真址：TO：Date：2011-04-21LTT Product Specification(Formal)7.0 Color TFT-LCD Model(800*480 16:9 )Model：LT70001DIT-02Note:1. Please contact LTT before designing your product based on this module specification.2. The information contained herein is presented merely to indicate the characteristics and performance of our products. No responsibility is assumed by LTT for any intellectual property claims or other problems that may result from application based on the module described herein.3. The mark “*” of Model means sub-model codeRecord of RevisionsDateSub-ModelDescription of change1.0May, 05, 2011A00/ A30Formal Product Specification was first released. Modify of label attachment on P0.Contents1.0General description.p.52.0Absolute maximum ratings.p.63.0Optical characteristics.p.74.0Block diagram. .p.105.0Interface pin connection.p.116.0Electrical characteristics.p.127.0Reliability test itemsp.168.0Outline dimension.p.179.0Package specification.p.1810.0General precaution .p.19GENERAL DESCRIPTION1.1 IntroductionLTT Display model LT70001-02 is a color active matrix thin film transistor (TFT) liquid crystal display (LCD) that uses amorphous silicon TFT as a switching device. This model is composed of a TFT LCD panel, a driving circuit , a touch panel, and a backlight system. This TFT LCD has a 7.0 inch diagonally measured active display area with VGA (800 horizontal by 480vertical pixel) resolution.1.2 Features 7.0 (16:9 diagonal) inch configuration 6 +FRC driver with 1 channel TTL interface Up/Down, Left/Right reversion selection RoHS Compliance1.3 Applications Personal Navigation Device Multimedia applications and Others AV system1.4 General informationItemSpecificationUnitNoteOutline Dimension165.00x 104.4 x 3.55 (Typ.)mmDisplay area153.6(H) x 86.64(V)mmNumber of Pixel800 RGB (H) x 480(V)pixels16:9 WVGAPixel pitch0.192*3(H) x 0.1805(V)mmPixel arrangementRGB Vertical stripe-Display modeNormally white-Surface TreatmentAntiglare-Dirver Elementa-Si TFT-LED24PCSEstablish2.0 ABSOLUTE MAXIMUM RATINGS2.1 Electrical Absolute Rating2.1.1TFT LCD ModuleItemSymbolMin.Max.UnitNotePower supply voltageVcccc-0.36.0VGND=0Vgh0.340VGND=0Vgl-200.3VGND=0AVdd0.515VAGND=0Vcom-0.56.0VLogic Signal Input LevelVi-0.3VDD +0.3V2.1.2Back-Light UnitItemSymbolTYP.Max.UnitNoteLED currentIL160-mA(1)(2)(3)LED voltageV9.6-V(1)(2)(3)Note(1) Permanent damage may occur to the LCD module if beyond this specification. Functional operation should be restricted to the conditions described under normal operating conditions.(2) Ta =252(3) Test Condition: LED current 20 mA. The LED lifetime could be decreased if operating IL is larger than 20 mA.2.2 Environment Absolute RatingItemSymbolMin.Max.UnitNoteOperating TemperatureTopa-2070Storage TemperatureTstg-30803.0 OPTICAL CHARACTERISTICS3.1Optical specificationItemSymbolConditionMin.Typ.Max.UnitNoteThreshold voltageVsat(6)Vth(6)Transmittance(With PZ)T5.8ContrastCR=0Normal viewing angle400500(1)(2)Response timeRisingTR57msec(1)(3)FallingTF2028White luminance(center)YL300320cd/m2I=160mAColor gamutS49%C lightColor chromaticity(CIE1931)WhiteWx0.2960.3110.326(1)(4) CF Glass C lightWy0.3410.3560.371RedRx0.6160.6310.646Ry0.3270.3420.357GreenGx0.3060.3210.336Gy0.5380.5530.568BlueBx0.1330.1480.163By0.1730.1880.203Viewing angleHor.LCR106070R6070Ver.U4050D5060Optima View DirectionOptima View Direction6 Oclock(5)3.2Measuring Condition Measuring surrounding: dark room LED current IL: 160mA Ambient temperature: 252oC 15min. warm-up time.3.3Measuring Equipment FPM520 of Westar Display technologies, INC., which utilized SR-3 for Chromaticity and BM-5A for other optical characteristics. Measuring spot size: 20 21mDURL=0=18012 Oclock=906 Oclock=270Note (1) Definition of Viewing Angle:Note (2) Definition of Contrast Ratio (CR): measured at the center point of paneLuminance with all pixels whiteCR = Luminance with all pixels blackNote (3) Definition of Response Time: Sum of TR and TF100%90%10%0%OpticalresponseTrTfWhite（TFT OFF）Black（TFT ON）White（TFT OFF）TimeNote (4) Definition of optical measurement setupNote (5) Rubbing Direction (The different Rubbing Direction will cause the differentoptimal view direction.Note (6) Definition of Vsat and Vth (at 200C4.0 BLOCK DIAGRAM4.1 TFT LCD Module4.2 Pixel Format1,11,21,31,424004802,1LCD Display Area480,1480,800BRRGR5.0 INPUT INTERFACE PIN ASSIGNMENTFPC connector is used for electronics interface.The recommended model is FH19SC-40S-0.5SH (51) manufactured by HIROSE.Pin No.SymbolI/OFunction1AGNDPAnalog Ground2AVDDPAnalog Power3VCCPPower voltage4R0IData input(LSB)5R1IData input6R2IData input7R3IData input8R4IData input9R5IData input10R6IData input11R7IData input(MSB)12G0IData input (LSB)13G1IData input14G2IData input15G3IData input16G4IData input17G5IData input18G6IData input19G7IData input(MSB)20B0IData input (LSB)21B1IData input22B2IData input23B3IData input24B4IData input25B5IData input26B6IData input27B7IData input (MSB)28DCLKIClock input29DEIData enable30HSDIHorizontal sync input. Negative polarity31VSDIVertical sync input. Negative polarity32MODE3IDE/SYNC mode select. normally pull high H;DE mode :HSD/VSD mode33RSTBIGlobal reset pin. Active low to enter reset state. Suggest to connecting with an RC reset circuit for stability .normally pull high.34STBYBIstandby mode, normally pull high STBYB=1,normal operation STBYB=0,timming control , source driver will turn off,all output are high-Z35SHLRPSource right or left sequence control. SHLR=L ,shift left :last data=S1SS2S1200=last data36VCCIDigital Power37UPDNIGate up or down scan control. UPDN=L , DOWN shift : G1-G2-G480 ; UPDN=H, up shift: G1-G2 AVDD - VGL - VGH - Data - B/L Power Off Sequence: B/L- Data - VGH - VGL - AVDD - VCCNotes: Data include R0R7, G0G7, B0B7, HSD, VSD, DCLK, SHLR, UPDN, DE MODE, RSTB, STBYB, SHLR, UPDN, DITH7.0 RELIABILITY TEST ITEMSNo.ItemConditionsRemark1High Temperature StorageTa=+80oC, 240hrs2Low Temperature StorageTa=-30oC, 240hrs3High Temperature OperationTa=+70oC, 240hrs4Low Temperature OperationTa=-20oC, 240hrs5High Temperature and High Humidity(operation)Ta=+60oC, 90%RH, 240hrs6Thermal Cycling Test (non operation)-30oC(30min) +80oC(30min), 200cycles7Electrostatic Discharge200V,200pF(0) 1 time/each terminal8Vibration1.Random:1.04Grms, 5500Hz, X/Y/Z,30min/each direction2. Sine: Freq. Range: 833.3Hz Stoke: 1.3mm Sweep: 2.9G, 33.3400Hz X/Z: 2hr, Y: 4hr, cyc : 15min9Shock100G, 6ms, X, Y, Z3 time for each directionJIS C7021, A-10(Condition A)10Vibration (with carton)Random: 0.015G2/Hz, 5200Hz-6dB/Octave, 200400HzXYZ each direction: 2hr11Drop (with carton)Height: 60cm1 corner, 3 edges, 6 surfacesJIS Z0202Note: There is no display function NG issue occurred, all the cosmetic specification is judged before the reliability stress.8.0 OUTLINE DIMENSIONLT43001DIT-01-V1 Unit: mmNote: General Tolerance: +/- 0.3mm9.0 PACKAGE SPECIFICATION 9.1 Packing form LCM ModelLCM Qty.in the boxInner Box Size (mm)NoticeLT70001DIT-0160 PCSTBD9.2 Packing assembly drawinLT70001DIT-024PCS/PA60PCS/BOX4PCS*15/PA10.0 GENERAL PRECAUTION 10.1 Use Restriction This product is not authorized for use in life supporting systems, aircraft navigation control systems, military systems and any other application where performance failure could be life-threatening or otherwise catastrophic. 10.2 Disassembling or Modification Do not disassemble or modify the module. It may damage sensitive parts inside LCD module, and may cause scratches or dust on the display. HannStar does not warrant the module, if customers disassemble or modify the module. 10.3 Breakage of LCD Panel 10.3.1 .If LCD panel is broken and liquid crystal spills out, do not ingest or inhale liquid crystal, and do not contact liquid crystal with skin. 10.3.2. If liquid crystal contacts mouth or eyes, rinse out with water immediately. 10.3.3. If liquid crystal contacts skin or cloths, wash it off immediately with alcohol and rinse thoroughly with water. 10.3.4. Handle carefully with chips of glass that may cause injury, when the glass is broken. 10.4 Electric Shock 10.4.1. Disconnect power supply before handling LCD module. 10.4.2. Do not pull or fold the LED cable. 10.4.3. Do not touch the parts inside LCD modules and the fluorescent LEDs conn