配置CME.docx

配置CMERequirementVoice-enable routerIP PhonePC Install CIPC-拓扑我们这里采用物理设备的目的为了测试DHCP服务，实验后部分，完全可以在模拟环境下测试。Voice-vlan 10Data-vlan 20Voice-vlan ip /24Data-vlan ip /24交换机根据需求做一下配置创建vlanSwitch#vlan database% Warning: It is recommended to configure VLAN from config mode,as VLAN database mode is being deprecated. Please consult userdocumentation for configuring VTP/VLAN in config mode.Switch(vlan)#vlan 10 name Voice-vlanSwitch(vlan)#vlan 20 name Data-vlanSwitch(vlan)#Switch(vlan)#apAPPLY completed.Switch(vlan)#exitAPPLY completed.Exiting.Switch#察看创建的vlanSwitch#show vlan briefVLAN Name Status Ports- - - -1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7. Fa0/810 Voice-vlan active20 Data-vlan active1002 fddi-default act/unsup1003 token-ring-default act/unsup1004 fddinet-default act/unsup1005 trnet-default act/unsupSwitch#把Fa0/1, Fa0/2 划入Voice Vlaninterface range fa 0/1 - 2switchport mode accessswitchport access vlan 20switchport voice vlan 10把路由器接口改成Trunk模式Interface fa 0/3switchport trunk encapsulation dot1qswitchport mode trunk把PC接口划入DataVlanInterface fa0/4Switchport mode accessSwitchport access vlan 20路由器配置两个字接口，分别放入Vlan10,20interface FastEthernet0/0no shut!interface FastEthernet0/0.10encapsulation dot1Q 10ip address 54 !interface FastEthernet0/0.20encapsulation dot1Q 20ip address 54 配置PC IP地址并指定网关测试pingRouter#ping 9Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 9, timeout is 2 seconds:!Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/8 msRouter#基础配置就完成了接下来我们开始关于CME的配置了首先创建Loopback口，作为CME的源，当然也可以直接使用借口地址。interface loopback 1ip address 55配置DHCP服务器。并且排除不希望分配出去的地址。ip dhcp excluded-address 9ip dhcp excluded-address 00 54ip dhcp pool voicenetwork /24default-router 54option 150 ip 可以通过show ip dhcp binding 察看ip地址分配情况。Router#show ip dhcp bindingBindings from all pools not associated with VRF:IP address Client-ID/ Lease expiration TypeHardware address/User name00 0100.1e4a.f332.1b Oct 01 2010 06:31 AM AutomaticRouter#-正式进入CME配置Router(config)#telephony-serviceRouter(config-telephony)#max-ephones 10Router(config-telephony)#max-dn 10Router(config-telephony)#ip source-address Router(config-telephony)#create cnf-filesCreating CNF filesCNF-FILES: Clock is not set or synchronized, retaining old versionStamps可以通过Router#show telephony-service 察看CME信息Router#show telephony-serviceCONFIG (Version=4.1(0)=Version 4.1(0)Cisco Unified Communications Manager ExpressFor on-line documentation please see:/univercd/cc/td/doc/product/access/ip_ph/ip_ks/index.htmip source-address port 2000max-ephones 10max-dn 10得知CME版本4.1 源地址 最大ephone数量10 最大DN数量1通过以下命令察看配置文件情况Router#show telephony-service tftp-bindingstftp-server system:/its/united_states/7960-tones.xml alias United_States/7960-tones.xmltftp-server system:/its/united_states/7960-font.xml alias English_United_States/7960-font.xmltftp-server system:/its/united_states/7960-font.xml alias English_United_States/7920-font.xmltftp-server system:/its/united_states/7960-dictionary.xml alias English_United_States/7960-dictionary.xmltftp-server system:/its/united_states/7960-kate.xml alias English_United_States/7960-kate.xmltftp-server system:/its/united_states/7960-kate.xml alias English_United_States/7920-kate.xmltftp-server system:/its/united_states/SCCP-dictionary.xml alias English_United_States/SCCP-dictionary.xmltftp-server system:/its/SEPDEFAULT.cnftftp-server system:/its/SEPDEFAULT.cnf alias SEPDftftp-server system:/its/XMLDf.xml alias XMLDf.xmltftp-server system:/its/ATADf.xmlRouter#这时电话应该可以自动注册上来了低版本的CME没有打开自动注册功能可以通过以下命令开启Router(config-telephony)#auto-reg-ephone*Nov 18 07:10:15.195: %IPPHONE-6-REGISTER_NEW: ephone-1:SEP001E4AF3321B IP:00 Socket:1 DeviceType:Phone has registered.ack CMERouter(config-telephony)#电话注册上来了，但是还不能食用,因为没有DN号，我们需要创建3个DNephone-dn 1number 1001ephone-dn 2number 1002ephone-dn 3numner 1003把DN 分配给电话Router(config)#ephone 1Router (config-ephone)#mac-address