注塑常用术语英文表达

1、1.雾气 Moisture Streaks2.玻纤安排不均 Glass Fiber Streaks3.困气 Gas Trap Effect4.银丝纹 Sliver Marks5.结合线 Weld Line6.水波痕 Water Wave Effect7.黑点 Dark Sport8.顶出印 Visible Ejector Marks9.变形 Deformation During Demolding10.填充不足 Short Filling11.冷料流痕 Cold Slug12.进胶口点不良 Dull Spots Near The Sprue13.喷射痕 Jetting14.表面起层 Flaki

2、ng Of The Surface Layer15.浮泡 Entrapped Air16.过热变色 Burnt Streaks17.龟裂 Stress Crack18.缩水痕 Sink Marks19.真空气泡 Density Bubble20.披锋 Flash21.擦伤印 Scratch MarksGlass fiber rich surface/glass emergence on the surface22 尺寸过大 Over dimension23尺寸过小 Under dimension 24 翘曲 Warpage/warped 25 收缩 Shrinkage/shrink 26 缩影

3、 Sink marks 27 打不满 Short shot/short molding 塑料模具mould of plastics 注塑模具injection mould 冲压模具die 模架mould base 定模座板Top clamping plate Top plate Fixed clamp plate 水口推板stripper plate A板A plate B板B plate 支承板 support plate 方铁 spacer plate 底针板 ejector plate 面针板 ejector retainer plate 回针 Return pin 导柱 Guide p

4、in 有托导套 Shoulder Guide bush 直导套 Straight Guide bush 动模座板Bottom clamp plate Moving clamp plate 基准线datum line 基准面datum plan 型芯固定板core-retainer plate 凸模固定板punch-retainer plate 顶针ejector pin 单腔模具single cavity mould 多腔模具multi-cavity mould 多浇口multi-gating 浇口gate 缺料starving 排气breathing 光泽gloss 合模力mould cla

5、mping force 锁模力mould locking force 挤出extrusion 开裂crack 循环时间cycle time 老化aging 螺杆screw 麻点pit 嵌件insert 活动镶件movable insert 起垩chalking 浇注系统feed system 主流道 sprue 分流道runner 浇口gate 直浇口direct gate , sprue gate 轮辐浇口spoke gate , spider gate 点浇口pin-point gate 测浇口edge gate 潜伏浇口submarine gate , tunnel gate 料穴col

6、d-slug well 浇口套sprue bush 流道板runner plate 排飞槽vent 分型线（面）parting line 定模stationary mould，Fixed mould 动模movable mould, movable half 上模upper mould， upper half 下模lower mould， lower half 型腔cavity 凹模cavity plate，cavity block 拼块split 定位销dowel 定位销孔dowel hole 型芯core 斜销angle pin, finger cam 滑块slide 滑块导板slide

7、guide strip 楔紧块heel block, wedge lock 拉料杆sprue puller 定位环locating ring 冷却通cooling channel 脱模斜度draft 滑动型芯slide core 螺纹型芯threaded core 热流道模具hot-runner mould 绝热流道模insulated runner mould 熔合纹weld line （flow line） 三板式模具three plate mould 脱模ejection 换模腔模具 interchangeable cavity mould 脱模剂release agent 注射力量sh

8、ot capacity 注射速率injection rate 注射压力injection pressure 差色剂colorant 保压时间holdup time 闭模时间closing time 定型装置sizing system 阴模female mould，cavity block 阳模male mould 电加工设备Electron Discharge Machining 数控加工中心CNC machine center 万能铁床Universal milling machine 卧式刨床Horizontal planer 车床Engine lathe 平面磨床Surface grinding machine