2015下半年春秋检工卡时控件项目tgc-a

1、TGC-A322141-01-1MEDForm.MP.001 版次Revi00第 1 页，共 5 页TitleDETAILED INSPECTION OF NOSE LANDING GEAR, BARREL,SLIDING TUBE AND TURNING TUBE EXTERNAL SURFA ,EXCEPT WHERE COVERED BY DRESSINGS AND BUSH FLANGEMech.Insp.WARNING:MAKE SURET THE GROUND SAFETY-LOCKS ARE INITION ON THE LANDING GEAR.警告： 确定地面安全销安装在起落

2、架上WARNING: MAKE SURET THE TRAVEL RANGES OF THE LANDING GEAR ARE CLEAR.警告：确定前起落架行程范围内无阻碍。Job Set-up/准备Safety Precautions/安全预防Make suret theROUND LOCK,NLG (D23080000) or PIN-LOCKING (MZ23080000) , asternative, is inition.确保前起落架地面安全锁销在位,锁销件号 D23080000 或 MZ23080000 二选一。he cockpit, on the right-center in

3、strument panel 400VU:- Put a WARNING NOTI) inition tols not to operate the landing-gear normal control-lever.在驾驶舱右侧 400VU 面板上：-放置一警告牌来告知其他人不要操作起落架正常控制手柄。(3) On the steering handwheels (CAPT and F/O) and on the brake pedals:- Put a WARNING NOTI) inition tols not to operate them.轮转弯手轮（机长和副驾侧）和刹车脚蹬：-放置

4、警告装置来通知其他人不要操作这些。(4) Put SAFETY BARRIER(S) inition.在工作区域设置安全围栏B. Aircraft Maenance Configuration /飞机构型(1)he cockpit, on the right-center instrument panel 400VU:- Make suret the landing-gear normal control-lever ishe DOWNition.在驾驶舱右侧 400VU 面板：-确保起落架正常控制手柄在 DOWN 位置(2) On the rudder/trim parking-brake

5、panel 110VU:- Make suret the free-fall control handle ishe usualition.在方向舵/配平停留刹车面板 110VU 上：-确保重力放起落架手柄在正常位置(3) Make suret CHOCK - WHEEL(S) are inition on the main landingTGC-A322141-01-1MEDForm.MP.001 版次Revi00第 2 页，共 5 页TitleDETAILED INSPECTION OF NOSE LANDING GEAR, BARREL,SLIDING TUBE AND TURNING

6、TUBE EXTERNAL SURFA ,EXCEPT WHERE COVERED BY DRESSINGS AND BUSH FLANGEMech.Insp.gear.确保主起落架的轮档已挡好。(4) Lift the aircrafthe forward jacking po(Ref. AMM TASK 07-11-00-581-003) .参考 AMM TASK 07-11-00-581-003顶点顶起飞机。C. Get Acs/接近Open the main doors of the NLG (Ref. AMM TASK 32-22-00-010-001) .打开前起落架舱门，参考 A

7、MM TASK 32-22-00-010-001Put an ACS PLATFORM 3M (10 FT)- ADJUSTABLE inition.在工作区域放置工作梯2.Procedure /程序(Ref. Fig. 607/TASK 32-21-00-991-009 SHEET 607.1) A. Detailed Inspection of NLG, Barrel, Sliding Tube and Turning Tube External Surfa详细检查前起落架外筒，滑筒和转筒外表面Do a detailed visual inspection of the barrel an

8、d look for signs of:Damage to the protective finishCracksDents and scratches.详细目视检查前起落架外筒（barrel），确保没有：-损伤到保护层-裂纹-凹坑和刮伤检查结果(Checking result)：处理措施(Maenance)：Do a detailed visual inspection of the turning tube external surfaand look for signs of:Damage to the protective finishCracksDents and scratches

9、.详细目视检查转筒外表面（turning tube external surfa），确保没有：RIITGC-A322141-01-1MEDForm.MP.001 版次Revi00第 3 页，共 5 页TitleDETAILED INSPECTION OF NOSE LANDING GEAR, BARREL,SLIDING TUBE AND TURNING TUBE EXTERNAL SURFA ,EXCEPT WHERE COVERED BY DRESSINGS AND BUSH FLANGEMech.Insp.-损伤到保护层-裂纹-凹坑和刮伤检查结果(Checking result)：处理措

10、施(Maenance)：Do a detailed visual inspection of the sliding tube and look for signs of:Damage to the protective finishCracksDents and scratches.详细目视检查滑筒（sliding tube），确保没有：-损伤到保护层-裂纹-凹坑和刮伤检查结果(Checking result)：处理措施(Maenance)：RIIClose-up /结束Close Acs/关闭接近Remove the acs platform(s).撤除接近Lower the aircra

11、ft on its wheels (Ref. AMM TASK 07-11-00-586-001) .降低飞机到地面，参考 AMM TASK 07-11-00-586-001Close the main door of the NLG (Ref. AMM TASK 32-22-00-410-001) .关闭前起落架舱门，参考 AMM TASK 32-22-00-410-001Put the aircraft back to its initial configuration. /恢复飞机到初始构型Remove the warning noti).拆下警告牌Remove the safety barriers.撤除护栏TGC-A322141-01-1MEDForm.MP.001 版次Revi00第 4 页，共 5 页TitleDETAILED INSPECTION OF NOSE LANDING GEAR, BARREL,SLIDING TUBE AND TURNING TUBE EXTERNAL SURFA ,EXCEPT WHERE COVERED BY DRESSINGS AND BUSH FLANGEMech.Insp.(3) Make suret the work area is clean and clear of tool(s) and other it