SPC-CPK-能力分析报告-标准版表格-统计过程控制-制程能力分析实战案例文档系列之一_第1页
SPC-CPK-能力分析报告-标准版表格-统计过程控制-制程能力分析实战案例文档系列之一_第2页
SPC-CPK-能力分析报告-标准版表格-统计过程控制-制程能力分析实战案例文档系列之一_第3页
SPC-CPK-能力分析报告-标准版表格-统计过程控制-制程能力分析实战案例文档系列之一_第4页
全文预览已结束

下载本文档

版权说明：本文档由用户提供并上传，收益归属内容提供方，若内容存在侵权，请进行举报或认领

文档简介

"0000有限公司

均值-极差控制图Xbar-R（Cpk、Ppk）",,,,,,,,,,,,,,,,,,,,,,,,,,

部门：,,生产科,,,工序名称：,,冲压,,,测量工具：,,数显卡尺,,,平均均值：,,12.81,,,平均极差：,,0.05,,,,

产品编号：,,J01C-1,,,设备名称：,,液压机,,,控制项目：,,冲压尺寸,,,控制上限：,,12.84,,,控制上限：,,0.10,,,,

产品名称：,,连接管,,,,,,,,规范：,,12.8±0.2,,,控制下限：,,12.79,,,控制下限：,,0.00,,,,

,,,,,,,,,,,,,,,,,,,,,,,,,日期：,

项目,,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25

"数

据

读

数",1,12.81,12.86,12.82,12.78,12.81,12.84,12.79,12.86,12.82,12.85,12.79,12.82,12.80,12.82,12.81,12.81,12.81,12.83,12.83,12.85,12.80,12.81,12.81,12.82,12.80

,2,12.80,12.87,12.83,12.77,12.85,12.79,12.78,12.79,12.80,12.83,12.80,12.80,12.80,12.81,12.79,12.83,12.80,12.80,12.81,12.81,12.83,12.82,12.83,12.77,12.83

,3,12.86,12.81,12.81,12.80,12.80,12.76,12.79,12.88,12.80,12.79,12.82,12.82,12.81,12.80,12.80,12.81,12.85,12.81,12.77,12.81,12.81,12.82,12.85,12.81,12.85

,4,12.84,12.84,12.79,12.81,12.86,12.77,12.81,12.81,12.82,12.79,12.81,12.80,12.82,12.81,12.81,12.83,12.81,12.81,12.83,12.82,12.77,12.83,12.82,12.82,12.80

,5,12.85,12.81,12.76,12.82,12.83,12.80,12.82,12.84,12.79,12.83,12.79,12.84,12.81,12.80,12.83,12.82,12.81,12.83,12.79,12.84,12.82,12.85,12.81,12.83,12.79

子组平均值,,12.83,12.84,12.80,12.80,12.83,12.79,12.80,12.84,12.81,12.82,12.80,12.82,12.81,12.81,12.81,12.82,12.82,12.82,12.81,12.83,12.81,12.83,12.82,12.81,12.81

平均均值,,12.81,12.81,12.81,12.81,12.81,12.81,12.81,12.81,12.81,12.81,12.81,12.81,12.81,12.81,12.81,12.81,12.81,12.81,12.81,12.81,12.81,12.81,12.81,12.81,12.81

控制上限,,12.84,12.84,12.84,12.84,12.84,12.84,12.84,12.84,12.84,12.84,12.84,12.84,12.84,12.84,12.84,12.84,12.84,12.84,12.84,12.84,12.84,12.84,12.84,12.84,12.84

控制下限,,12.79,12.79,12.79,12.79,12.79,12.79,12.79,12.79,12.79,12.79,12.79,12.79,12.79,12.79,12.79,12.79,12.79,12.79,12.79,12.79,12.79,12.79,12.79,12.79,12.79

子组极差,,0.06,0.06,0.07,0.05,0.06,0.08,0.04,0.09,0.03,0.06,0.03,0.04,0.02,0.02,0.04,0.02,0.05,0.03,0.06,0.04,0.06,0.04,0.04,0.06,0.06

平均极差,,0.05,0.05,0.05,0.05,0.05,0.05,0.05,0.05,0.05,0.05,0.05,0.05,0.05,0.05,0.05,0.05,0.05,0.05,0.05,0.05,0.05,0.05,0.05,0.05,0.05

控制上限,,0.10,0.10,0.10,0.10,0.10,0.10,0.10,0.10,0.10,0.10,0.10,0.10,0.10,0.10,0.10,0.10,0.10,0.10,0.10,0.10,0.10,0.10,0.10,0.10,0.10

控制下限,,0.00,0.00,0.00,0.00,0.00,0.00,0.00,0.00,0.00,0.00,0.00,0.00,0.00,0.00,0.00,0.00,0.00,0.00,0.00,0.00,0.00,0.00,0.00,0.00,0.00

子组标准差=,,#NUM!,#NUM!,#NUM!,#NUM!,#NUM!,#NUM!,#NUM!,#NUM!,#NUM!,#NUM!,#NUM!,#NUM!,#NUM!,#NUM!,#NUM!,#NUM!,#NUM!,#NUM!,#NUM!,#NUM!,#NUM!,#NUM!,#NUM!,0.0316,#NUM!

,,,,,,,,,,,,,,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,,,,,,,,,,,,

过程能力和性能研究：,,,,,,,,,,,,,,,,,,,,,,,,,,

平均均值,,,,,,12.814160,,,,均值控制上限,,,,,12.8422,,,估计过程标准偏差,,,,,,0.0208,,

平均极差,,,,,,0.0484000,,,,均值控制下限,,,,,12.7861,,,,,,,,,,,

规格上限,,USL=,13,,,,,,,极差控制上限,,,,,0.1021,,,,,,,,,,,

规格下限,,LSL=,12.600,,,,,,,极差控制下限,,,,,0.0000,,,,,,,,,,,

常数表,,,,,,,,,,,,,,,,,,,,,,,,,,

n,2,3,4,5,6,7,8,,,能力指数,,,,,3.21,,,性能指数,,,,,,2.92,2.92,

D4,3.27,2.57,2.28,2.11,2,1.92,1.86,,,上限能力指数,,,,,2.98,,,上限性能指数,,,,,,2.71,2.71,

D3,0,0,0,0,0,0.08,0.14,,,下限能力指数,,,,,3.44,,,下限性能指数,,,,,,3.13,3.13,

A2,1.88,1.02,0.73,0.58,0.48,0.42,0.37,,,过程能力指数,,,,,2.98,,,过程性能指数,,,,,,2.71,2.71,

d2,1.13,1.69,2.06,2.33,2.53,2.7,2.85,,,过程能力评价,,过程能力很充足！,,,,,,过程性能评价,,,过程性能很充足！,,,,,

,,,,,,,,,,,,,,,,,,,,,,,,,,,

,,,,,分组,频率,分布,,,,,,,,,,,,,,,,,,,

最大值,,12.880,,,12.7420,0.0000,0.1184,,,,,,,,,,,,,,,,,,,

最小值,,12.760,,,12.7540,0.0000,0.5429,,,,,,,,,,,,,,,,,,,

极差,,0.120,,,12.7660,2.0000,1.8888,,,,,,,,,,,,,,,,,,,

,,,,,12.7780,5.0000,4.9852,,,,,,,,,,,,,,,,,,,

,,,,,12.7900,15.0000,9.9821,,,,,,,,,,,,,,,,,,,

,,,,,12.8020,19.0000,15.1629,,,,,,,,,,,,,,,,,,,

,,,,,12.8140,30.0000,17.4731,,,,,,,,,,,,,,,,,,,

,,,,,12.8260,18.0000,15.2751,,,,,,,,,,,,,,,,,,,

,,,,,12.8380,16.0000,10.1303,,,,,,,,,,,,,,,,,,,

ôs=,0.022831,(,,),12.8500,14.0000,5.0966,,,,,,,,,,,,,,,,,,,

,,,,,12.8620,4.0000,1.9452,,,,,,,,,,,,,,,,,,,

,,,,,12.8740,1.0000,0.5632,,,,,,,,,,

人人文库> 全部分类> 教育资料 > 辅导培训

温馨提示

  • 1. 本站所有资源如无特殊说明，都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
  • 2. 本站的文档不包含任何第三方提供的附件图纸等，如果需要附件，请联系上传者。文件的所有权益归上传用户所有。
  • 3. 本站RAR压缩包中若带图纸，网页内容里面会有图纸预览，若没有图纸预览就没有图纸。
  • 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
  • 5. 人人文库网仅提供信息存储空间，仅对用户上传内容的表现方式做保护处理，对用户上传分享的文档内容本身不做任何修改或编辑，并不能对任何下载内容负责。
  • 6. 下载文件中如有侵权或不适当内容，请与我们联系，我们立即纠正。
  • 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

最新文档

评论

0/150

提交评论