模德MT-11000皮纹ppt课件

1、六. 咬 花 粗 度 比 較 / 精 密測 試,以下是使用德國 HOMMEL TESTER T1000 型表面粗度測定器所測出 表面粗度, 深度及圖形, 藉此可 明白區分噴砂, 梨地,皮紋及寫真等類花 紋之不同. 主要符號說明如下: Ra: 算 術平 均 粗 度 值 Rz: 山 谷 平 均 值 Rm: 最 大 山 谷 深 度 值 噴 砂 梨 地 皮 紋 寫 真 NO:12 NO:9 NO:NH4044 柄 NO:26,15 mm,15 mm,15 mm,15 mm,Hommer Tester T1000 C - 320 Dat:- Nr:-,Hommer Tester T1000 C - 32

2、0 Dat:- Nr:-,Hommer Tester T1000 C - 320 Dat:- Nr:-,Hommer Tester T1000 C - 320 Dat:- Nr:-,Lt = 15 mm Lc = 2.5 mm Ra = 04.53 Um Rz = 26.92 Um Rm = 32.16 Um Nr = 00057/cm,Lt = 15 mm Lc = 2.5 mm Ra = 12.18 Um Rz = 58.84 Um Rm = 64.88 Um Nr = 00023/cm,Lt = 15 mm Lc = 2.5 mm Ra = 09.81 Um Rz = 56.24 Um

3、Rm = 64.32 Um Nr = 00032/cm,Lt = 15 mm Lc = 2.5 mm Ra = 23.79 Um Rz = 91/.16Um Rm = 92.64 Um Nr = 00012/cm,TEXTURE #,DRAFT,DEEP.,TEXTURE #,DRAFT,DEEP.,MOLD-TECH 咬花製作參考資料,MT-11000 MT-11010 MT-11020 MT-11030 MT-11040 MT-11050 MT-11060 MT-11070 MT-11080 MT-11090 MT-11100 MT-11110 MT-11120 MT-11130 MT-1

4、1040 MT-11150 MT-11160,1? MIN,1.5 2.5 3 4.5 6.5 4.5 4.5 3 5.5 9 4 3 4 4 4 6,.0004 .001 .0015 .002 .003 .0045 .003 .003 .002 .0035 .006 .0025 .002 .0025 .0025 .00275 .004,MT-11200 MT-11205 MT-11210 MT-11215 MT-11220 MT-11225 MT-11230 MT-11235 MT-11240 MT-11245 MT-11250 MT-11255 MT-11260 MT-11265 MT-1

5、1270 MT-11275 MT-11280,4.5 4 5.5 6.5 7.5 6.5 4 6 2.5 3 4 3 6 7 6 5 8,.003 .0025 .0035 .0045 .005 .0045 .0025 .004 .0015 .002 .0025 .002 .004 .005 .004 .0035 .0055,TEXTURE #,DRAFT,DEEP.,TEXTURE #,DRAFT,DEEP.,MOLD-TECH 咬花製作參考資料,MT-11300 MT-11305 MT-11310 MT-11315 MT-11320 MT-11325 MT-11330 MT-11335 MT

6、-11340 MT-11345 MT-11350 MT-11355 MT-11360 MT-11365 MT-11370 MT-11375 MT-11380,3.5 7.5 7.5 1.5 4 4.5 3 3 4.5 4.5 5.5 4 5.5 7 6 6 6,.0025 .005 .005 .001 .0025 .003 .002 .002 .003 .003 .0035 .0025 .0035 .0045 .004 .004 .004,MT-11400 MT-11405 MT-11410 MT-11415 MT-11420 MT-11425 MT-11430 MT-11435 MT-114

7、40 MT-11445 MT-11450 MT-11455 MT-11460 MT-11465 MT-11470 MT-11475 MT-11480,3 4 5.5 3 4 5.5 10 15 1.5 2.5 4 4.5 5.5 7.5 3 3 4.5 ,.002 .0025 .0035 .002 .0025 .0035 .007 .010 .0005 .0015 .0025 .003 .0035 .005 .002 .002 .003,七.塑料與咬花深度,1. 脫模度預留 0.5 度或 0.005 mm 深/安全量 2. tolerance is +/- 0.0025mm (Hommel Tester T1000 精密測試),3. PS,(0.005mm) 0.0002,ABS,PC,(0.005mm) 0.0002, 黏度 (viscosity) / 流動長度 ,4. exp: apple G-1 texture minimum draft required:3.5度 for ABS & PC, 2.5度 for PVC,PLASTIC SPECIFICATION STEEL SPECIFICATION = DEPTH NR DEPTH NR (in/1000) pk/in (in/1000) pk/in (Microns) pk/cm (