panabit安装配置.doc

Freebsd系统安装1.1 Vmware workstion 6.5 下安装 freebsd vmware 设置注意事项三块网卡全为 “桥接模式”：1.1.2 freebsd安装 按“q”退出分区设置按“a”键按”s”键盘，按“q”退出按”a, 然后按”q”退出多核CPU，把SMP选上选”NO”配置IP.Vmware有三块网卡，假定把em0设置为管理接口, em1,em2 数据接口.1 Panabit安装设置.1.1进入系统开启ssh服务 Login: root 密码为空设置root密码编辑ssh服务配置文件修改 PermitRootLogin no 为PermitRootLogin yes ，使root用户能登录。启动ssh服务在windows xp 使用 ssh工具连接freebsd2.2.1 sftp 上传panabit安装包上传安装包并安装bashliu# ls.cshrc .login Panabit0903.tar.tar.k5login .profilebashliu# time tar xf Panabit0903.tar.tar 0.044u 0.429s 0:01.14 40.3% 71+486k 5+403io 2pf+0wbashliu# cd Panabit0903bashliu# lsadmin etc ipeupgrade rdfbin ipeinstall kernelbashliu# ./ipeinstall Welcome installing panabit!Please input the directory to install panabit /usr/panabit:Please input the directory to store log /usr/panalog:Please input the directory to store configuration /usr/panaetc:The last time to verify your choice:(1) The directory that you want to install is /usr/panabit(2) The directory that the log to be stored is /usr/panalog(3) The directory that the configuration to be stored is /usr/panaetcAbove are right(y/ny)?yCreating directory /usr/panabit .okCreating directory /usr/panalog .okInstalling Panabit to /usr/panabit .okInitializing configurations .okSaving configuration to /etc/PG.conf .* Congratulations *!You have successfully installed Panabit on your system:(1) The installed path is: /usr/panabit(2) The log path is: /usr/panalog(3) The configuration path is: /usr/panaetcTo make your system more sutiable for panabit running, itsrecomended of tuning your system according your system memorysize and cpu frequence.Do you want to tune your system(y/n)y: yYour kernel configuration has been tuned as the followings:kern.ipc.nmbclusters=10240kern.maxdsiz=2000000000You should restart your system to make they take effects.Warning: your em driver has been compiled into kernel. To optimize panabit performance, we recommend you use the optimized driver panaos provides. To use the optimized driver, please remove em driver from your kernel.Following interfaces are installed in your system: em0 em1 em2Please choose one of above as your admin interface:em0 设置管理接口Please input ip address of admin interface: 管理接口IPPlease input network mask of admin interface: #子网掩码Please input default gateway: 网关The following interfaces are left for your data processing: em1 em2 Please select data interfaces: em1 em2数据接口Your interface configurations are: Admin interface : em0 Admin ip address : Admin netmask : Default gateway : Data interfaces : em1 em2Thank you for using panabit!You can issue /usr/panabit/bin/ipectrl start to start panabit!And you can also add the above command to /etc/rc.local fileto let the system automaticly start panabit at system startup!If you want to stop the currently running panabit, you can issue/usr/panabit/bin/ipectrl stop to stop it!bashliu# /usr/panabit/bin/ipectrl start启动panabitkldload: cant load /usr/panabit/kernel/if_em.ko: File existsWarning: fail to load optimized em driverPlease recompile your kernel without em enabled!Otherwise, you cant get the maximum performanceof panaos provides!kern.jos.ipe_netdevices: - em1 em2net.inet.tcp.msl: 30000 - 2000Load module pci . em1bus2:1:0: 0x8086:0x100f em2bus2:2:0: 0x8086:0x100fLoad module cmds .Load module dma .This is standard version, no PANAOS DMA supported!Load module mgmt .Load module mbuf . jos_mbuf_minit: 64 mbuf allocatedLoad module intf .Load module em .JOSEM not installed!Load module bsd . interface em1 attached, mac address 00:0C:29:C1:A0:14 bring interface em1 upnetwork is started!Starting ipe_httpd .ipe_httpd is started!ipe_monitor is started!/usr/panabit/bin/ipe_httpd: started as root without requesting chroot(), warning onlydata monitor is started!bashliu# Load module axpdesc .Load module cmds .Load module dbf .dbf_minit: logpath is /usr/panalog, internal is 360dbf_load: log file not exist!Load module chart . interface em2 attached, mac address 00:0C:29:C1:A0:28 bring interface em2 upLoad module ipe .Load module axpdef .Load module watcher .Load module tbucket .Load module key .Load module keytable .Load module flow . flow size 64, entry size 64Load module node . table size 32768, pool size 30000,node size 32Load module xping .Load module port .port module initialzied, max port 65536Load module axpgrp .Load module protocol .Load module appobj . appobj pool size 500, entry size 32Load module localip .Load module iptable .Load module vlink .Load module policy_scheduler .Load module license .Load module thread .Load module logger .Load module flow . share CPU with control plane!Load module config .This is standard version, no license needed!Warning: no configuration file foundLoad module josdbf .panaos startup!PANAOS is assigning cpu 0 to thread loggerThread logger now is running .PANAOS is assigning cpu 0 to thread flowThread flow now is running .flow(0x83af400) start executing.bashliu# echo /usr/panabit/bin/ipectrl start /etc/rc.local2.2.2 用浏览器访问panabit管理界面用户名: admin 密码: panabit3.1 问题排除1,web页面无法访问?1) 首先确定 https服务是否正常启动bashliu# netstat -ant | grep 443tcp4 0 0 *.443 *.* LISTENtcp6 0 0 *.443 *.* LISTEN以上说明https服务已经启动如果没有显示那么bashliu# /usr/panabit/bin/ipectrl start 启动panabit 2) 其次确定管理接口名及其ip是否设置正确bashliu# ifconfig #查看网络接口名称，例如 em0em0: flags=8843 mtu 1500 options=b inet netmask 0xffffff00 broadcast 55 ether 00:0c:29:c1:a0:1e media: Ethernet autoselect (1000baseTX ) status: activeem1: flags=8943 mtu 1500 options=b ether 00:0c:29:c1:a0:14 media: Ethernet autoselect (1000baseTX ) status: activeem2: flags=8943