FANUC PMC中文英文报警对照表.docx

FANUC PMC中文英文报警对照表对于有的机床编写的报警是英文或者英文的缩写，看起来不明确，以下是个人整理的对照表，方便人阅读。T WORD ERROR（T 码错误）LOW OIL LEVEL（油位低）SPINPLE FAULT（主轴故障）SPINDLE ALARM（主轴报警）EXTERNAL EMG STOP（急停按钮被按下）AC NOT READY（交流盘未准备好）SPINPLE LUBE FAULT（主轴润滑故障）T CODE ERROR（T代码出错，非法T代码）M CODE ERROR（M代码出错，非法M代码）SERVO NOT READY（伺服未准备好）NC NOT READY（NC没准备好）TURRET FAULT（转塔故障）TURRET LIMIT（转塔限位）DC 24V OPEN（直流24断开）+24V NOT READY（+24V没准备好）GRAR DRIFT（档位漂移）PLEASE AXIS RETURN HOME（轴未回零）PLEASE DRUM RETURN HOME（刀库未回零）AIRPRESSFAILURE（气压故障）UNCL TOOL FALL（松刀失败）AIR PRESSURE DROP（压缩空气压力过低）CLAMP TOOL FALL（夹刀失败）DRUM NOT PARKED（刀库未在原值）X ZERO POINT NOT REACHED（X 轴未回零）Y ZERO POINT NOT REACHED（Y 轴未回零）Z ZERO POINT NOT REACHED（Z 轴未回零）4TH ZERO POINT NOT REACHED（第4轴未回零）X AXIS OVERTR*L（X轴超限）Y AXIS OVERTR*L（Y轴超限）Z AXIS OVERTR*L（Z轴超限）COUNTER SWITCH REEOR（计数开关故障）MASTERT RANSFER OVER TEMP（主变压器过热）Z AXIS NOT AT FIRST REF POSITION（Z轴未在第一参考点）SPINDLE ORIENTATION FALLURE（主轴定向失败）TOOL DESENT OR TOOL DATA REEOR（刀具数据错误）PLEASE UNLOAD THE TOOL ON SPRINELK（请卸下主轴上的刀）PLEASE LOAD TOOL ON APINDLE（请装上主轴上的刀）A AXIS UNCLAMP FAIL（A 轴松开失败）A AXIS CLAMP FAIL（A 轴夹紧失败）DRUM OUT TO APRONDLEIS FALL（刀库摆向换刀位失败）MG SWING OVERLOAD（刀库摆动过载）DRUM BACK PARK IS FALL（刀库摆回原始位失败）TURRENT MOTOR1 OVERLOAD（刀库移动电机过载）COOLANT MOTOR OVERLOAD（冷却泵过载）DRUM ATC FAULT（自动换刀失败）TOOLS UNLOCKED（刀具未锁紧）BATTERY ALARM（电池报警）DRUM POSITION SWITCH ERROR（刀库位置检测开关故障）DRUM NOW NOT AT PARK（刀库未在原始位置）IT DANGOU TO MOVE DRUM（刀库禁动）POT UO FAILOR POT NOT AT UP POSITION（刀套未在水平位）POT DOWN FAIL（刀套翻下动作失败）IT IS DANGOUR TO MOVE ARM（机械手禁动）THE SPINDLE STATU IS ERROR（主轴状态错误）ARM MOTOR OR ARM SWITCH FALL（机械手或机械手开关故障）CENTRE LUBRICATION FALL（中心润滑故障）THE WORK NOT CLAMPED（工件未夹紧）AUTO TOOL CHANGE FAULT（自动换刀失败）TOOL DATA OUT OF RANGE（指令刀具号超出范围）THE ORDER TOOL NOW IN SPINDLE（目标刀具在主轴上）THE THREE SPINDLE SWITCH FAULT（主轴上的接近开关）THE CENTRE COOLANT IS LOWER（刀具内冷泵液位过低）DRUM RETURN 1# POSITION FAULT（刀库自动回零失败）SPINDLE OVERLOAD（主轴过载）TURRENT MOTOR OVERLOAD（刀盘转动电机过载）CHIP CONVEYER OVERLOAD（拉屑器过载）HARD LIMIT OR SERVO ALARM（硬限位或伺服报警）NO LUB OIL（无润滑油）INDEX HEAD UNLOCKED（分度头未锁紧）MT NOT READY（机床没准备好）MG OVERLOAD（刀库过载）LUB EMPTY（润滑无油）AIR PRESSURE（气压不足）COOLANT NOT READY（冷却没准备好）LUBE EMPTY（油雾油位低，润滑油位低）LUB PRESSURE LOW（润滑压力低）CONVEY VERLOAD（排屑过载）LUB OVERLOAD（润滑过载）LUBE PRESSURE LOW（油雾压力低）SERIAL SPINDLE ALARM (串行主轴报警)NC BATTERY LOW ALARM(NC电池低报警)MAGAZINE MOVE LIMIT SWITCH ERRORSPINDLE TOOL UNLAMP POSITION LIMIT SWITCH ERRORMAGAZINE NOT IN POSITION OR SENSOR ERRORAIR PRESSURE LOW ALARM(气压低报警)MOTOR OVERLOAD(电机过载)T CODE MAGAZINE TOOLST CODE 1 ERROR5TH AXIS HARDWARE OVERTR*ER LIMIT ERRORDOOR IS OPENED(开门)LUB PRESSURE SWITCH ERROR(油压开关错误)SPINDLE OIL COOLANT UNIT ERRORSPINDLE LOAD ABNORMAL（主轴负荷异常）TRANSDUCER ALARM（传感器报警）BED-HEAD LUBRICATE OFF（床头润滑关闭）EMG OFFHYDRAULIC CHUCK PRESS LOW（液压夹头压力低）HYDRAULIC TAIL PRESS LOW（液压尾座压力低）LUB 0IL LOW（油压低）TURRET CODE ERROR（转塔码错误）TURRET RUN OVERTIME（转塔运行超时）MANUAL HANDLE INTERRUPTTRY TO RUN SPINDLE WHILE CHUCK NOT LOCKTRY TO RUN SPINDLE WHILE TAIL NOT LOCKSPINDLE NEUTRAL GEARMAGAZINE ADJUSTHYDRAULIC NOT RUNSAFETY DOOR BE OPENEDSAFETY DOOR NOT CLOSENOT ALL AXIS H*E GONE BACK REFIN ADJUST,IGNORE GOING BACK REFAFTER EXCHANGE TOOL,CYCLE STARTATC MOTOR QF16 OFFX AXIS IS LOCKED（X 轴被锁定）Y AXIS IS LOCKED（Y 轴被锁定）Z AXIS IS LOCKED（Z 轴被锁定）A AXIS IS LOCKED（A 轴被锁定）SPINDLE MOTOR FAN QF26 OFF(主轴电机风扇QF26关闭)关注我们的微信公众号shukongzhpngguo，获取更多数控技术文章。SPINDLE ORIENTATION INCOMPLETE（主轴定位不完全）M FUNCTION NOT COMPLETE（M 功能无法完成）SPINDLE NOT IN GEAR POSITION（齿轮不在主轴位置）SPINDLE NOT CHANGED TO LOW GEAR（主轴没有变为低档）SPINDLE NOT CHANGED TO HIGH GRAR（主轴没有变为高档）MAG NOT BACKWARDSPINDLE TOOL NOT CLAMPSPINDLE TOOL NOT UNCLAMPMAG NOT IN POSITIONMAG DOES NOT ROTATEMAG DOES NOT STOP RUNNINGA AXIS H*E NOT CLAMPEDA AXIS H*E NOT UNCLAMPEDSET D499=1,”MAG.JOG” SWITCH ONHYDRAULIC MOTOR QF7 OFF（ 液压马达QF7关闭 ）HYDRAULIC TEMPRETURE HIGH（ 液压使用温度高 ）HYDRAULIC FILTER BLOCKED（液压过滤器阻止）HYDRAULIC OIL LEVEL LOW（ 液压油位低 ）HYDRAULIC FAN QF8 OFF（液压风扇QF8关闭）HELIX CONYER QF9 OR QF10 OFFCHAIN CONYER QF11 OFFCOOLANT MOTOR QF12 OFF（冷却液电机QF12关闭）COOLNT LEVEL LOW,CYCLE STOP AFTER 20 MINUTESINNER COOLANT BLOCK（内冷却堵塞）SPINDLE COOLANT MOTOR QF14 OFF（主轴冷却液电机QF14关闭）INNER COOLANT QF13 OFF（内冷却液QF13关闭）MAG MOTOR QF15 OFFCABINET COOLANT EQUIP QF20 OFFOIL GATHER QF24 OFFAIR PRESSURE LOW（低气压）SPINDLE COOLANT MOTOR FAULT（主轴冷却液电机故障）LUB.OIL IS LOW（润滑油低）DOOR OPEN（门打开）FRONT DOOR(R) OPEN（前门打开）LEFT DOOR OPEN（左门打开）LUBRICATION OIL QF23 OFF（润滑油QF23关闭）LUBRICATION PRESS LOW（润滑油位低）IN ADJUST,MAG CANT EXCHANGE T（在调整，刀库不能交换T）NOT ALL DOOR CLOSED（门没有全部关闭）IN M06,MAG NOT READY（在M06，刀库未准备好）MAGAZINE NOT READY（刀库未准备好）POCKET NOT HORIZANTALIN M06,Z NOT BACK TO 2ND REFIN M06,Z AXIS NOT IN PSW1ATC NOT IN ZERO POSITIONSPINDLE ORIENTATION UNCOMPLETEPOCKET NOT HOR./MAG NOT BCKWRDPOCKET NOT VER./MAG NOT FORWRDUNCLAMP TOOL HAS NOT COMPLETEDCLAMP TOOL HAS NOT COMPLETEDAIM TOOL NO. IS WRONGMAG NOT BACKWARDAFTER RETRACT,SET R.T.BACK OFFZ NOT IN PSW2,FORBID ATC RUNNINGD499 EQUAL 1MAG.JOG SOFT SWITCH IS ONZ NOT IN PSW2,FORBID MAG FORWARDCHEKE SPINDLE MODULE ALARMOIL WATER SEPARATOR QF24 OFFSET THE SOFT SWITCH MAG.JOG OFFSET D499 TO 0设定D499为0K PARAM ABOUT MAG SET IS WRONG关于MAG的K参数设定错误MECHANICAL BRAKE NOT RELEASED机床抱闸没有松开MECHANICAL BRAKE IS WRONG机床抱闸错误PLEASE ADD LUB.OIL请加润滑油PROBE BATTERY VOLTAGE IS LOW探头电池电压低PROBE IS ERR探头错误PARAMETER WRITE ENABLE（参数写使能）PMC EDIT ENABLE（PMC编辑使能）CHECK LUB ROUTINSPINDLE GEAR SIGNAL MISS主轴档位信号消失T_CLAMPED_SIGNAL MISS T夹紧信号消失SP OVERRIDE SWITCH DISCONNECTION主轴倍率开关断路FEED OVERRIDE SWITCH DISCONNECTION进给倍率开关断路THE TOTAL NUMBER OF POCKETS SET ERRCHANGE T STOPED BECAUSE NO AIR因为缺少压空交换停止THE COOLANT WATER TOO LOW,ADD COOLANT WATER AT ONCE冷却水少立即加水COOLANT LEVEL LOW,ADD COOLANT WATER冷却水液位低PLEASE REPLACE CNC BATTERY QUICKLY请立即更换CNC电池SIEMENS常用缩略语A Output输出ASCII American Standard Code for Information Interchange美国信息交换标准代码* Preparation for work运行准备BA Operating mode运行方式BAG Operating mode groups运行方式组BB Ready for operation准备好运行BCD Binary Coded Decimals二-十进制BHG Hand-held terminal手提终端BOF User interface用户接口CNC Computerized Numerical Control计算机化数字控制CP Communication Processor通迅处理器CPU Central Processing Unit计算机中央处理装置CR Carriage Return托架折回CSB Central Service Board(PLC module)中央维护板，PLC 模块CTS Clear To Send发送使能DAU Digital-Analog Converter数模转换器DB Data Block数据块DIN German Industrial Standards德国工业标准DIO Data Input/Output数据输入/输出DRF Differential Resolver Function差分功能DRY Dry Run空运行DSB Decoding Single Block译码单段DSR Data Send Ready备用输入DW Data Word数据字E Input输入EIA-Code Special tape code,number of holes per characters always odd特殊纸带码，每个字符的孔数为奇数EPROM Programm memory with fixed program有固定程序的程序存储器E/R Controlled Supply and Energy Recovery Module可控电源和能量恢复模块ETC ETC key:Extension of the softkey bar in the same menuETC键：同级菜单扩展键FDB Product designation database产品指定数据库FIFO First in First Out先进先出FRA Frame module帧频模块FRAME Coordinate conversion with the components zerooffset，rotation，scaling，mirror-imaging坐标换算，具有零点偏置，坐标旋转，标度功能和镜向功能FRK Cutter radius compensation铣刀半径补偿FST Feed Stop停止进给GUD Global User Data全体用户数据HMS High-Resolution Measuring System高分辨率测量系统HSA Main Spindle Drive主轴驱动HW Hardware硬件IM Interface Module接口模块IM-S/R Interface Module(S=send/R=receive)接口模块，S=发送/R=接收INC Increment步进增量ISO-Code Special tape code,number of holes per character always even特殊纸带码，每个字符的孔数为偶数K1k4 Channel 1 to Channel 4通道1 到通道4KOP Ladder Diagram梯形图KV Loop-Gain Factor增益系数KUE Transformation Ratio传动比LCD Liquid Crystal Display液晶显示LED Light Emitting Diode发光二极管显示LUD Local User Data局部用户数据MB Megabyte兆字节MD Machine Data机床数据MK Measuring Circuit测量回路MDA Manual Data Automatic手动输入，自动执行MLFB Machine-readable product designation机器可识别的产品代号MMC Man Machine Communication:User interface of the numerical controlsystem for operation,programming and simulation人机通讯：系统操作界面，用操作，编程和模拟MPF Main Program File：NC part program(main program)NC零件程序，主程序MPI Multi Point Interface多点通讯接口MSTT Machine control panel机床控制面板NC Numerical Control数字控制NCK Numerical Control Kernel(numerical krnel with block preparation,traversing range etc.)数字控制核心：具有程序段预处理,运行范围等等NCU Numerical Control Unit数控单元NURBS Non Uniform Rational B Spline非均值有理B样条NV Zero Offset零点偏置OEM Original Equipment Manufacturer原设备制造商OP Operator Panel操作面板OPI Operator Panel Interface操作面板接口PC Personal Comprter个人计算机PCMCIA Personal Computer Menory Card International Association接口协议PG Programming Device编程器PLC Programmable Logic Control可编程逻辑控制器PRT Program Test程序测试RAM Random Access Memory随机存取存储器RISC Reduced Instruction Set Computer处理器，具有指令组小、通过能力强ROV Rapid Override快速修调RPA R Parameters Active(NCK memoty area for R parameter numbers)R参数有效，NCK 中用于R 参数号