液晶风淋控制器F4H中英文说明书

1、 语 音 风 淋 室 说明书一. 概述风淋室自控系统主要用于风淋室、货淋室及风淋通道的自动控制。可自动实现内、外门的互锁与解锁；照明的启停；人体自动感应以及风机的启停等功能。产品在自动流程时有相关语音提示，并具有风淋时间、前后门解锁延时时间、照明延时间可调等灵活功能。二. 主板面膜示意图及按键说明 液晶语音风淋室控制器，图文界面,可与PLC相媲美，具有强大的功能，可随时进入系统改变参数，以满足客户的需要，语音系统有中文、英文二种可选用。LCD voice air shower controller, graphic interface, can be comparable with PLC,

2、With a powerful function, can be entered at any time to change the parameters of the system to meet the needs of customers, the voice system has two kinds of Chinese and English can be selected. 面板功能说明：Touch screen function description一、面板示意图(1). Touch screen sketch map 二、面板按键(2). Panel key Power ON

3、/OFF电源键：开启/关闭系统 Light ON/OFF照明键：开启/关闭照明 / 退出键Lighting key: Turn on / off lighting/ Exit key Clean ON风淋键：手动开启风淋 / 确认键Showering key: Manual opening air shower/ Confirm key +PB 1、设定时间参数增量 增量键： 2、选择模式上移 UP key: 1. Setting Times.2. Select mode. -PB 1、设定时间参数减量 减量键： 2、选择模式下移 DOWN key: 1. Setting Times.2. S

4、elect mode. RESET 复位键： 紧急情况使用Emergency stop key: Emergency use三、图标示意图四、参数设置(4).Parameter setting在控制面板上同时按住键和键5秒后，进入系统设置参数。进入后，键为确认键，键为退出键，键和键为选择工程和增减数值,所有工程设置结束后，按键确认，并退出(或5秒后自动确认并退出)。On the control panel, hold the key and key for 5 seconds as the same time to enter the system setting parameters.Aft

5、er entering, the key to confirm key, key for the exit key, key andkey to select items and increase or decrease value, All project settings after the end of the key to confirm, and exit (or 5 seconds after the automatic recognition and exit).风淋时间快速设置：按住键或键5秒后，快速进入“b-01风淋时间设置，5秒后自动确认并退出。Air shower tim

6、e quick setting: hold key or key for 5 seconds, quickly enter the "b-01" air shower time set, 5 seconds after the automatic confirmation and exit.参数表工程参数范围出厂值模式选择01：红外连锁，单向吹风，仅有红外1可配置循环02：红外连锁，双向吹风，仅有红外104：红外自动，单向吹风，有双红外05：红外自动，双向吹风，双风机，有双红外红外1控制高速风机, 红外2控制低速风机08：连锁自动，单向吹风09：连锁自动，双向吹风01时间设

7、置01：风淋时间0-999秒1005：进门延时解锁0-255秒006：出门延时解锁0-255秒010：风淋结束，出门延时解锁时间0-255秒011：照明延时时间0-60分112：风淋结束，进门延时解锁时间0-255秒0循环设置01：无循环0102：一次循环01：风淋结束，进、出门关闭后，循环开启的等待时间0-255秒502：循环运行时间0-255秒1003：间断循环01：风淋结束，进、出门关闭后，循环开启的等待时间0-255秒502：循环运行时间0-255秒1003：循环间断时间0-255秒1004一直循环进、出门开闭5秒后，循环启动出厂默认000：保持当前数据001：参数恢复出厂值Param

8、eter tableItemParameter rangeFactory valueMode selection01：Infrared sensor interlocking Single direction showering02：Infrared sensor interlocking two-way showering04：Infrared sensor automatic Single direction showering, have two infrared sensor05：Infrared sensor automatic two-way showering，double fa

9、n，have two infrared sensorsensor 1control high speed fan, sensor 2 control low speed fan08：Infrared sensor interlocking automatic door Single direction showering09：Infrared sensor interlocking automatic door two-way showering01Time setting01：Showering time0-999s1005：Inlet door delay unlocked time0-2

10、55s006：Outlet door delay unlocked time0-255s010：Showering end，outlet door delay unlocked time0-255s011：Lighting delay time0-60 min112：Showering end，inlet door delay unlocked time0-255s0Cycle setting01：No cycle0102：Once cycle01：showering end, inlet and outlet door closed, Cycle open waiting time0-255

11、s502：cycle running time0-255s1003：Intermittent cycle01：showering end, inlet and outlet door closed, Cycle open waiting time0-255s502：cycle running time0-255s1003：cycle Intermittent time0-255s1004:Always cycleInlet and outlet door closed cycle start after 5 secondsMake defaultMake default to recover

12、factory setting000：001：default一、 风淋室正常操作过程：2. Air shower normal operation process一、初始化自检(1). Initialize the self-inspection翻开电源，面板液晶屏点亮，同时微电脑控制器做一次检测，显示当前的模式(闪烁3次),进出门是否关闭，红外探头与反光板是否对准。如系统有故障，将在屏幕上显示代码，并语音提示。Turn on the power, LCD display, the screen flashes 3 times, at the same time, a microcompute

13、r controller to do a test, Is the inlet and outlet door closed? Infrared probe and reflective board is aligned. If the system is faulty, the code will be displayed on the screen, and voice prompts.二、正常工作状态(2). Normal working state接通电源380V带零线，指示灯由红色变为绿色，液晶屏点亮，风淋室处于自动状态。The 380 v power supply is conne

14、cted (with zero wire),Power LED red light turns green, the screen display, air shower in the automatic state.三、从非洁净区进入洁净区(3). From Non clean area enter clean area手拉门红外线连锁Manual door (Infrared sensor interlocking)开启进门，出门自动上锁，风淋室出门指示灯为红色30秒后，进门仍未关闭，那么语音提示“请关门，且在液晶屏上有图标闪烁，人员进入风淋室，经红外探头，关闭进门，风淋启动0999s可调

15、，语音提示“风淋中，请转身，此时进出门均上锁，指示灯均为红色，风淋倒计时结束语音提示“风淋结束，请离开，开启出门，人员走出风淋室，出门关闭，整个过程结束。Open the inlet door, outlet door automatic locked, air shower outlet door indicator light is red (30 seconds later, inlet door is not closed, then the voice prompts " close the door, please!" and on the screen hav

16、e flashing icon) and personnel to enter the air shower, through infrared sensor, closed the inlet door, the air shower running (0 999s can be adjustable, and the voice prompt "showering, please turn"), this time inlet and outlet door was locked, indicator light red, when showering end (voi

17、ce prompt "showering end, please leave), open the outlet door, personnel leave air shower, closed the outlet door, the whole process end.资料个人收集整理，勿做商业用途四、从洁净区退出非洁净区(4). From clean area to non clean area手拉门Manual door开启出门，进门自动上锁，风淋室进门指示灯为红色30秒后，出门仍未关闭，语音提示“请关门，且在液晶屏上有图标闪烁，人员进入风淋室风淋不启动，关闭出门，开启进门，

18、走出风淋室，关闭进门，整个过程结束。Open the outlet door, inlet door automatic locked, air shower inlet door indicator light is red (30 seconds later, outlet door is not closed, voice prompts "close the door, please!" and on the screen icon flash) an personnel to enter the air shower, air shower does not st

19、art, outlet door closed, open the inlet door, personnel leave air shower, closed the inlet door, the whole process end.五、连锁控制(5). Interlocking control进出门连锁控制局部，分别安装于进出门外那么。Inlet door and outlet door interlocking control part, respectively installed on the inlet and outlet door.风淋室待机时，进出门指示灯亮绿灯。Air s

20、hower standby, inlet and outlet door indicator light is green1) 开进门，出门上锁，出门指示灯亮红灯，进门指示灯亮绿灯。1) Open the inlet door, outlet door locked, outlet door indicator light is red, inlet door indicator light is green.2) 开出门，进门上锁，进门指示灯亮红灯，出门指示灯亮绿灯。2) Open the outlet door, inlet door locked, inlet door indicato

21、r light is red, outlet door indicator light is green.3) 风淋室在运转时，进、出门均锁定，指示灯亮红灯。3) Air showering is running, inlet and outlet door locked, indicator light is red.4) 在停电、紧急停止时，进、出门处于解除状态。4) When the power cut, emergency stop, inlet door an outlet door in the unlock state六、计数器Counter 风淋室每运行一次，计数一次Air s

22、hower once every run, count once三、故障排除方法：3. Fault shooting method:一、故障排除(电源故障)(1). Fault shooting (power fault)开启总电源保POWER灯不亮保总电源是否开启保NOYES 控制器故障保Controller fault保Main power on保Is the main power on?保Power LED OFF display保二、故障排除(照明故障)(2). Fault shooting (lighting fault)NO总电源是否开启保开启总电源保控制器故障，是否有220V保控

23、制器故障保开启日光灯按钮保POWER灯不亮保日光灯不亮保YESYES更换日光灯灯管保日光灯按钮是否开启保NOYESNO日光灯图标是否亮保NO不亮亮日光灯电子整流器故障保O K.Main power on保Lamp not bright保NOIs the main power on?Controller fault，Have 220V?保Controller fault保Turn on the lamp保Power LED OFF displany保YESYESReplace lamp保Is the lamp switch turn on?保NOYESNOLamp icon is bright？

24、保NONOOKLamp electronicRectifier fault保O K.三、故障排除电锁故障(3). Fault shooting (electric lock fault)进/出门锁故障保POWER亮绿灯保液晶屏点亮保锁与锁片是否错位保NONONO开启进/出门保确认电锁是否有DC12V保检查线路是否短路保NOYESYES调整门上锁片或门框上电锁保控制器故障保电锁故障保 Screen display保Inlet/outlet door lock fault保Power on保Lock and lock plate dislocation?保Open inlet/outlet doo

25、r保NONONOHave DC12V?保Check wireWhether short circuit保NOYESYESAdjust the door unlocked or frame on the electric lock保Controller fault保Lock fault保四、风淋不吹淋故障一(4). Air shower not showering fault 1POWER亮绿灯保液晶屏点亮保无法自动风淋保风淋图标是否显示保按风机按钮保YESYES三相触头是否磨损烧坏保接触器是否跳脱保NONO更换接触器保控制器故障保NOO K.Screen display保Power on保No

26、t showering保Air shower icon is displayed?保Contactor trip?保YESPush fan button保YESThree-phase contact burn out?保NONOReplace contactor保Contactor fault保NOO K.五、风淋不吹淋故障二(5). Air shower not showering fault 2进入风淋室保确认出入方向正确保液晶屏点亮保POWER亮绿灯保进门电锁故障或锁片错位N对N保NO出门图标是否亮保更换电锁或调整位置N对N故障代码C1保接触器是否故障保NO翻开进门保YES更换接触器保YES更换门电锁或调整位置N对N故障代码C2保出门电锁故障或锁片错位N对N保NO进门图标是否亮保翻开出门保Enter air shower保Confirm the correct direction保Screen displa